Nowe rodzaje cieczy przemywających osady z płuczki inwersyjnej przed zabiegiem cementowania otworów wiertniczych Cementowanie rur okładzinowych do ścian otworu jest niezwykle ważnym etapem w procesie wiercenia, uzależnionym przede wszystkim od właściwego oczyszczenia przestrzeni pierścieniowej z płuczki wiertniczej i powstałych w trakcie wiercenia osadów filtracyjnych. Jednym z głównych wymogów stawianych przed zabiegiem cementowania jest uzyskanie maksymalnie szczelnego wypełnienia przestrzeni pierścieniowej i trwałego połączenia między rurami a ścianą otworu. Odpowiednie przygotowanie otworu do zabiegu cementowania zakłada wytłoczenie płuczki i usunięcie ze ścian otworu powstałych osadów filtracyjnych i zanieczyszczeń. Proces oczyszczania otworu nabiera szczególnej wagi podczas zastosowania do wiercenia płuczki olejowodyspersyjnej. Płuczki olejowodyspersyjne to jedne z najmniej kompatybilnych cieczy wiertniczych z zaczynem cementowym. Nieprawidłowe wytłoczenie płuczki i pozostawienie nieusuniętej warstwy olejowej na ścianach otworu może być przyczyną zanieczyszczenia zaczynu cementowego płuczką, nieprawidłowego wypeł-nienia przestrzeni pierścieniowej przez zaczyn, zmniejszenia przyczepności związanego zaczynu cementowego do ściany otworu i rur okładzinowych, zmniejszonej integralności strukturalnej i słabej izolacji międzystrefowej. W artykule przedstawiono badania laboratoryjne nad opracowaniem składu cieczy przemywającej skutecznie rozpuszczającej i usuwającej zanieczyszczenia olejowe powstałe podczas wiercenia otworu po płuczce inwersyjnej przed zabiegiem cementowania kolumn rur okładzinowych. Opracowana ciecz przemywająca powinna charakteryzować się wysoką skutecznością oczyszczania osadów z płuczki olejowodyspersyjnej, być kompatybilna z płuczką wiertniczą i zaczynem cementowym oraz zapobiegać tworzeniu się emulsji wodno-olejowych. Zastosowanie nowo opracowanej cieczy przemywającej przed zabiegiem cementowania powinno także wpłynąć na zwiększenie przyczepności zaczynu cementowego do ścian otworu i lepsze wypełnienie przestrzeni pierścieniowej.Słowa kluczowe: płuczka inwersyjna, ciecz przemywająca, ciecz rozdzielająca, osady płuczkowe. New types of preflush fluids removing invert emulsion drilling mud filter cake prior to casing cementingCasing cementing is an extremely important step in the drilling process, which is primarily dependent on the proper cleaning of the annular space, which involves the removal of drilling mud and filter cake. The main goals of cementing is to get the maximum/tightest filling of the annular space and a permanent connection between casing and wall. Proper preparation of the hole before the cementing operation involves removing of drilling mud from the hole and cleaning filter cake from the wall. Cleaning the borehole becomes particularly important when oil-based mud was used during drilling. This is due to the fact that the oil-based drilling muds are not very compatible with cement slurries. Incomplete removal of mud and leaving a layer of oil on the wall of the hole, can cau...
Wiercenie otworów w warunkach występowania wysokich ciśnień i temperatury najczęściej realizowane jest przy zastosowaniu płuczek olejowodyspersyjnych, które-z uwagi na swoje właściwości-kwalifikują je do celów HTHP. Jednym z ważniejszych zagadnień występujących podczas wiercenia głębokich otworów jest dostosowanie właściwości płuczki do panujących warunków otworowych. Płuczka musi charakteryzować się wysoką odpornością temperaturową, zapobiegać uszkodzeniu złoża i innym zagrożeniom związanym z wierceniem otworów w warunkach HTHP. W artykule przedstawiono wyniki badań laboratoryjnych odporności opracowanej płuczki inwersyjnej na działanie wysokiego ciśnienia i temperatury. Przeprowadzone badania umożliwiły także ocenę oddziaływania płuczki na skały ilasto-łupkowe oraz określenie jej wpływu na przepuszczalność skał zbiornikowych dla ropy i gazu. Słowa kluczowe: płuczka inwersyjna, faza olejowa, stabilność emulsji, warunki HTHP. Analysis of the technological properties of invert emulsion drilling mud in HTHP conditions Drilling holes in conditions of high pressure and high temperature (HTHP) is often realized by using invert emulsion drilling muds, due to their properties. One of the major tasks that occur during drilling deep holes is to adjust mud properties to borehole conditions, that can lead to safe and efficient exploitation. The drilling mud must have high temperature resistance, must prevent formation damage and other threats related to drilling under HTHP conditions. The article presents the results of laboratory tests on the developed invert emulsion mud resistant to high pressure and temperature. The studies also enabled the evaluation of drilling mud impact on clay-shale rocks and its effect on the permeability of reservoir rocks.
Drilling boreholes in gas zones and in zones with the possibility of migration or gas exhalation requires a high index of well tightness. An important parameter determining the effectiveness of sealing the annular space is the adhesion of the cement sheath to the rock formation. Low values of adhesion of the cement sheath to the rock formation and to the casing surface result in the formation of uncontrolled gas flows. The lack of adhesion also reduces the stabilization of the pipe column. To obtain the required adhesion, the annular space should be properly cleaned. Thorough removal of filter cake from the drilling fluid increases adhesion and reduces gas migration from the annular space. Therefore, in this work, the authors focus on determining the effect of cleaning the annular space on the adhesion of the cement sheath to the rock formation. The results of the research work allow for further research on the modification of spacers and cement slurries in order to obtain the required increase in adhesion. The article presents the issues related to the preparation of the borehole for cementing by appropriate cleaning of the rock formation from the residue of the mud cake. During the implementation of the works, tests of cleaning the rock surface are performed. The obtained results are correlated with the results of adhesion on the rock–cement sheath cleaned of the wash mud cake contact. When analyzing the obtained test results, a relationship is found between the cleaning of the rock surface and the adhesion of the cement sheath to it.
An analysis of the possibilities of using new types of polymeric inhibitors in the technology of drilling fluids in shale formations The paper presents an overview of the currently used inhibited drilling fluids with the ability to reduce the hydration of the shale. Based on literature data the possibility of using drilling muds in shale formations was analysed. The rest of the article presents the results of research intended to select new chemicals used as inhibitors of the hydration of rocks in drilling muds for drilling in shale. In this study agents such as a new type of polyglycol, an alkoxy derivative of butanol and an amine compound were used. New types of inhibitors were used in the composition of drilling fluids developed for drilling in shale. The carried out investigations of thermal resistance, resistance to pollution with mono-and multivalent ions, and studies on their impact on the disintegration of Miocene shale have shown that the developed muds have suitable technological parameters, are resistant to pollution with bivalent metal ions and temperature, and provide effective protection against Miocene shale hydration up to 100%. The investigations were performed under the Blue Gas project.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.