The aim of this study was to find a safe, effective sterilization method that does not destroy the bone-inductive capacity of demineralized bone implants. Five sterilizing agents were tested in rats. Implants procured and processed under sterile conditions served as controls. New bone formation was evaluated by determining dry weight, calcium content, and Sr-85 incorporation of the induced ossicles. Glutaraldehyde solution, formaldehyde gas, and ethylene oxide destroyed almost all the bone-inductive capacity. Irradiation by 2.5 Mrads Co-60 resulted in a loss of about half of the inductive capacity. Merthiolate (0.18 per cent) was the only sterilizing agent that did not reduce the bone-inductive capacity of the demineralized implants. Because merthiolate is not sporicidal, gamma irradiation appears to be the most appropriate sterilizing agent for demineralized bone in clinical use.

No abstract

Significant knowledge and data gaps associated with the fate of product-embedded engineered nanomaterials (ENMs) in waste management processes exist that limit our current ability to develop appropriate end-of-life management strategies. This review paper was developed as part of the activities of the IWWG ENMs in Waste Task Group. The specific objectives of this review paper are to assess the current knowledge associated with the fate of ENMs in commonly used waste management processes, including key processes and mechanisms associated with ENM fate and transport in each waste management process, and to use that information to identify the data gaps and research needs in this area. Literature associated with the fate of ENMs in wastes was reviewed and summarized. Overall, results from this literature review indicate a need for continued research in this area. No work has been conducted to quantify ENMs present in discarded materials and an understanding of ENM release from consumer products under conditions representative of those found in relevant waste management process is needed. Results also indicate that significant knowledge gaps associated with ENM behaviour exist for each waste management process investigated. There is a need for additional research investigating the fate of different types of ENMs at larger concentration ranges with different surface chemistries. Understanding how changes in treatment process operation may influence ENM fate is also needed. A series of specific research questions associated with the fate of ENMs during the management of ENM-containing wastes have been identified and used to direct future research in this area.

The potential colloids release from a large panel of 25 solid industrial and municipal waste leachates, contaminated soil, contaminated sediments and landfill leachates was studied. Standardized leaching, cascade filtrations and measurement of element concentrations in the microfiltrate (MF) and ultrafiltrate (UF) fraction were used to easily detect colloids potentially released by waste. Precautions against CO(2) capture by alkaline leachates, or bacterial re-growth in leachates from wastes containing organic matter should be taken. Most of the colloidal particles were visible by transmission electron microscopy with energy dispersion spectrometry (TEM-EDS) if their elemental MF concentration is greater than 200 μgl(-1). If the samples are dried during the preparation for microscopy, neoformation of particles can occur from the soluble part of the element. Size distribution analysis measured by photon correlation spectroscopy (PCS) were frequently unvalid, particularly due to polydispersity and/or too low concentrations in the leachates. A low sensitivity device is required, and further improvement is desirable in that field. For some waste leachates, particles had a zeta potential strong enough to remain in suspension. Mn, As, Co, Pb, Sn, Zn had always a colloidal form (MF concentration/UF concentration>1.5) and total organic carbon (TOC), Fe, P, Ba, Cr, Cu, Ni are partly colloidal for more than half of the samples). Nearly all the micro-pollutants (As, Ba, Co, Cr, Cu, Mo, Ni, Pb, Sb, Sn, V and Zn) were found at least once in colloidal form greater than 100 μgl(-1). In particular, the colloidal forms of Zn were always by far more concentrated than its dissolved form. The TEM-EDS method showed various particles, including manufactured nanoparticles (organic polymer, TiO(2), particles with Sr, La, Ce, Nd). All the waste had at least one element detected as colloidal. The solid waste leachates contained significant amount of colloids different in elemental composition from natural ones. The majority of the elements were in colloidal form for wastes of packaging (3), a steel slag, a sludge from hydrometallurgy, composts (2), a dredged sediment (#18), an As contaminated soil and two active landfill leachates. These results showed that cascade filtration and ICP elemental analysis seems valid methods in this field, and that electronic microscopy with elemental detection allows to identify particles. Particles can be formed from dissolved elements during TEM sample preparation and cross-checking with MF and UF composition by ICP is useful. The colloidal fraction of leachate of waste seems to be a significant source term, and should be taken into account in studies of emission and transfer of contaminants in the environment. Standardized cross-filtration method could be amended for the presence of colloids in waste leachates.

Labille et al. Environmental Risk of Nanoparticulate UV-Filters formulation to the knowledge of the risk involved in this choice all along the product lifecycle, an eco-design approach can be achieved where release or toxicity are reduced. Sustainability can thus be accounted for, during the design process, by making the appropriate choices (in advance) that help minimize or prevent the environmental impact of the sunscreen.