A systematic study of the degree of molecular ordering and swelling of different nanocellulose model films has been conducted. Crystalline cellulose II surfaces were prepared by spin-coating of the precursor cellulose solutions onto oxidized silicon wafers before regeneration in water or by using the Langmuir-Schaefer (LS) technique. Amorphous cellulose films were also prepared by spin-coating of a precursor cellulose solution onto oxidized silicon wafers. Crystalline cellulose I surfaces were prepared by spin-coating wafers with aqueous suspensions of sulfate-stabilized cellulose I nanocrystals and low-charged microfibrillated cellulose (LC-MFC). In addition, a dispersion of high-charged MFC was used for the buildup of polyelectrolyte multilayers with polyetheyleneimine on silica with the aid of the layer-by-layer (LbL) technique. These preparation methods produced smooth thin films on the nanometer scale suitable for X-ray diffraction and swelling measurements. The surface morphology and thickness of the cellulose films were characterized in detail by atomic force microscopy (AFM) and ellipsometry measurements, respectively. To determine the surface energy of the cellulose surfaces, that is, their ability to engage in different interactions with different materials, they were characterized through contact angle measurements against water, glycerol, and methylene iodide. Small incidence angle X-ray diffraction revealed that the nanocrystal and MFC films exhibited a cellulose I crystal structure and that the films prepared from N-methylmorpholine-N-oxide (NMMO), LiCl/DMAc solutions, using the LS technique, possessed a cellulose II structure. The degree of crystalline ordering was highest in the nanocrystal films (approximately 87%), whereas the MFC, NMMO, and LS films exhibited a degree of crystallinity of about 60%. The N,N-dimethylacetamide (DMAc)/LiCl film possessed very low crystalline ordering (<15%). It was also established that the films had different mesostructures, that is, structures around 10 nm, depending on the preparation conditions. The LS and LiCl/DMAc films are smooth without any clear mesostructure, whereas the other films have a clear mesostructure in which the dimensions are dependent on the size of the nanocrystals, fibrillar cellulose, and electrostatic charge of the MFC. The swelling of the films was studied using a quartz crystal microbalance with dissipation. To understand the swelling properties of the films, it was necessary to consider both the difference in crystalline ordering and the difference in mesostructure of the films.

The effects of fungal cellulases on model cellulose films were studied using a high-resolution quartz crystal microbalance (QCM) sensitive to minute changes of the nanometer thick model cellulose films. It was found that endoglucanases not only produce new end groups but also cause a swelling of the cellulose film. The cellobiohydrolases degraded the films quickly, which was detected as a rapid decrease in the remaining amount of cellulose on the QCM crystal. However, changing viscoelastic properties of the films also indicated a softening of the film during the degradation. A defined mixture of selected cellulases caused a significantly higher rate of degradation than only cellobiohydrolases. Cellulase synergism is discussed with the endoglucanase swelling effects and film softening added.

Traditional seasoning of wood chips normally results in significant yield losses and brightness reduction due to the uncontrolled action of microorganisms. Techniques for reduction of the amount of wood extractives with minimal yield and brightness loss are therefore of interest for the pulp and paper industry. To study a biotechnological approach for reduction of wood extractives, wood chips from sapwood of Scots pine (Pinus sylVestris) and Norway spruce (Picea abies) were treated with a commercial albino strain of the sap stain fungus Ophiostoma piliferum. During 2 weeks of controlled seasoning, the content of wood extractives decreased by approximately 40% for Scots pine and 25% for Norway spruce, where the triglyceride contents were degraded to a greater degree. Thermomechanical pulps were produced from untreated and pretreated pine chips. The properties of these pulps and corresponding laboratory sheets were investigated. The pretreated pulps showed less shortened fibers, lower amounts of triglycerides, and enhanced strength properties. The mechanisms behind these effects are discussed. Furthermore, the ability of the albino Ophiostoma piliferum to displace mould growth from wood chips was investigated in a series of experiments. It was concluded that the fungus should preferably be inoculated on fresh chips in order to repress mould growth.