This work introduces a phenomena-based model for delignification in the kraft pulping process. The solubilization of lignin is described as a set of chemical reactions representing the entire chemistry of lignin degradation as well as dissolution of the degraded lignin. For modeling, reaction mechanisms and reactions kinetics derived mainly from the literature were used. Each reaction was simulated separately and then combined for the overall degradation. The model was validated with experimental results from pine wood meal pulping under a wide range of reaction parameters. The experimental data presented a good fit with the model. With the aid of the model, the structure and the amount of wood components, in fibers and black liquor, can be determined at any pulping stage. Several engineering parameters can be computed from the detailed chemical composition of liquor and wood or chemical pulp. These include, e.g., kappa number, brightness, yield, active alkali, effective alkali, sulfidity, and higher heating value.
The article introduces a detailed model for carbohydrate chemistry in kraft pulping. This article is continuation to the modeling work carried out for hot water extraction and chemical pulp bleaching. The model includes galactoglucomannan, xylan, and cellulose acid-base equilibria, in addition to peeling, stopping, and alkaline hydrolysis reactions of the same carbohydrates, as well as hexenuronic acid formation and degradation reactions. The Arrhenius parameters were applied from the literature or regressed against experimental data in the present study. The model is very successful in predicting the experimental data of carbohydrate reactions during kraft pulping. Many features of the pulping-related model can be applied to specific fractionation chemistry considerations. The detailed knowledge on carbohydrates composition at any stage of pulping gives possibility for further development of biorefinery cases based on kraft pulping, such as biofuel and chemicals production.
Bio-based products can help us to reach sustainability goals and reduce our dependency on fossil-based raw materials. Lignin is an abundantly available bio-based material. Recently, a concept of an alkali–O2 oxidation (LigniOx) process for feasibly producing lignin dispersants at a kraft pulp mill has been introduced. The oxidation process uses O2 gas to increase the anionic charge of lignin and the final oxidized lignin can serve as a concrete plasticizer or versatile dispersant. Life cycle assessment (LCA) is a tool widely used to holistically evaluate the environmental benefits of various products. The goal of this study was to evaluate the versatility of the novel lignin dispersants produced from kraft lignin and to compare the environmental performance with the synthetic products using an attributional cradle-to-gate LCA. Results showed that LigniOx impacts were lower than synthetic equivalents for both the end uses—superplasticizer and dispersants—in most of the impact categories. The only negative impact was on eutrophication that arises from fly ash purging at the kraft pulping process even without the integrated LigniOx production. In addition, the production of LigniOx lignin appeared to be more attractive than conventionally recovered kraft-lignin. LigniOx contributed minimally to the total impacts with the majority of impacts arising from the kraft pulping process.
The purpose of this study was to elucidate the structures and functional properties of tannin- and lignin-derived nano- and microparticles and the coatings prepared from them. Nanoparticles prepared from technical lignins and water-insoluble tannin obtained from softwood bark showed large differences in the suspension testing of antibacterial efficacy against methicillin-resistant Staphylococcus aureus (MRSA) bacteria. A common factor among the most effective lignin nanoparticles was a relatively low molar mass of the lignin, but that alone did not guarantee high efficacy. Tannin nanoparticles showed good antibacterial activity both in suspension testing and as coatings applied onto cellulose. The nanoparticles of nitrogen-modified tannin and the small microparticles of nitrogen-modified kraft lignin exhibited promising flame-retardant parameters when applied as coatings on cellulose. These results illustrate the potential of nano- and microsized particles of unmodified and chemically modified polyphenols to provide functional coatings to cellulosic substrates for environments and applications with high hygiene and fire safety requirements.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.