Silicon dominates the electronics industry, but its poor optical properties mean that III-V compound semiconductors are preferred for photonics applications. Photoluminescence at visible wavelengths was observed from porous Si at room temperature in 1990, but the origin of these photons -highly-localized defect states or quantum confinement effects? -has been the subject of intense debate ever since. Since then attention has shifted from porous Si to Si nanocrystals, but the same fundamental question about the origin of the photoluminescence has remained. Here we show, based on measurements in high magnetic fields, that defects are the dominant source of light from Si nanocrystals. Moreover, we show that it is possible to control the origin of the photoluminescence in a single sample: passivation with hydrogen removes the defects, resulting in photoluminescence from quantum-confined states, but subsequent UV illumination reintroduces the defects, making them the origin of the light again.

The formation process of titania based nanorods during hydrothermal synthesis starting from an amorphous TiO2.nH2O gel has been investigated. Sodium tri-titanate (Na2Ti3O7) particles with a rodlike morphology were prepared by a simple hydrothermal process in the presence of a concentrated NaOH aqueous solution. The ion exchange reaction of the synthesized Na2Ti3O7 nanorods with HCl under ultrasonic treatment promotes a complete sodium substitution and the formation of H2Ti3O7 nanorods. Low-temperature annealing of the as-produced nanorods of Na2Ti3O7 and H2Ti3O7 leads to a loss of the layered crystal structure and the formation of nanorods of condensed framework phases-sodium hexa-titanate (Na2Ti6O13) and metastable TiO2-B phases, respectively. These transformations proceed without a significant change in particle morphology. The nanostructures were investigated by scanning electron microscopy (SEM), powder X-ray diffraction (XRD), the Brunauer-Emmett-Teller (BET) method, thermogravimetric analysis (TGA), and Raman spectroscopy. The structural defects of the synthesized nanorods were investigated by high-resolution electron microscopy. The presence of planar defects can be attributed to the exfoliation of the zigzag ribbon layers into two-dimensional titanates as well as to the condensation of the layers of TiO6 octahedra into three-dimensional frameworks.

The gas-phase loading of [Zn4O(bdc)3] (MOF-5; bdc = 1,4-benzenedicarboxylate) with the volatile compound [Ru(cod)(cot)] (cod = 1,5-cyclooctadiene, cot = 1,3,5-cyclooctatriene) was followed by solid-state (13)C magic angle spinning (MAS) NMR spectroscopy. Subsequent hydrogenolysis of the adsorbed complex inside the porous structure of MOF-5 at 3 bar and 150 degrees C was performed, yielding ruthenium nanoparticles in a typical size range of 1.5-1.7 nm, embedded in the intact MOF-5 matrix, as confirmed by transmission electron microscopy (TEM), selected area electron diffraction (SAED), powder X-ray diffraction (PXRD), and X-ray absorption spectroscopy (XAS). The adsorption of CO molecules on the obtained Ru@MOF-5 nanocomposite was followed by IR spectroscopy. Solid-state (2)H NMR measurements indicated that MOF-5 was a stabilizing support with only weak interactions with the embedded particles, as deduced from the surprisingly high mobility of the surface Ru-D species in comparison to surfactant-stabilized colloidal Ru nanoparticles of similar sizes. Surprisingly, hydrogenolysis of the [Ru(cod)(cot)]3.5@MOF-5 inclusion compound at the milder condition of 25 degrees C does not lead to the quantitative formation of Ru nanoparticles. Instead, formation of a ruthenium-cyclooctadiene complex with the arene moiety of the bdc linkers of the framework takes place, as revealed by (13)C MAS NMR, PXRD, and TEM.