No abstract

High precision mobile sensing of multi-species gases is greatly demanded in a wide range of applications. Although quantum cascade laser absorption spectroscopy demonstrates excellent field-deployment capabilities for gas sensing, the implementation of this measurement technique into sensor-like portable instrumentation still remains challenging. In this paper, two crucial elements, the laser driving and data acquisition electronics, are addressed. Therefore, we exploit the benefits of the time-division multiplexed intermittent continuous wave driving concept and the real-time signal pre-processing capabilities of a commercial System-on-Chip (SoC, Red Pitaya). We describe a re-designed current driver that offers a universal solution for operating a wide range of multi-wavelength quantum cascade laser device types and allows stacking for the purpose of multiple laser configurations. Its adaptation to the various driving situations is enabled by numerous field programmable gate array (FPGA) functionalities that were developed on the SoC, such as flexible generation of a large variety of synchronized trigger signals and digital inputs/outputs (DIOs). The same SoC is used to sample the spectroscopic signal at rates up to 125 MS/s with 14-bit resolution. Additional FPGA functionalities were implemented to enable on-board averaging of consecutive spectral scans in real-time, resulting in optimized memory bandwidth and hardware resource utilisation and autonomous system operation. Thus, we demonstrate how a cost-effective, compact, and commercial SoC can successfully be adapted to obtain a fully operational research-grade laser spectrometer. The overall system performance was examined in a spectroscopic setup by analyzing low pressure absorption features of CO at 4.3 μm.

Instrumentation for environmental monitoring of gaseous pollutants and greenhouse gases tends to be complex, expensive, and energy demanding, because every compound measured relies on a specific analytical technique. This work demonstrates an alternative approach based on mid-infrared laser absorption spectroscopy with dual-wavelength quantum cascade lasers (QCLs). The combination of two dual-and one single-DFB QCL yields high-precision measurements of CO (0.08 ppb), CO 2 (100 ppb), NH 3 (0.02 ppb), NO (0.4 ppb), NO 2 (0.1 ppb), N 2 O (0.045 ppb), and O 3 (0.11 ppb) simultaneously in a compact setup (45 × 45 cm 2 ). The lasers are driven time-multiplexed in intermittent continuous wave mode with a repetition rate of 1 kHz. The individual spectra are real-time averaged (1 s) by an FPGA-based data acquisition system. The instrument was assessed for environmental monitoring and benchmarked with reference instrumentation to demonstrate its potential for compact multi-species trace gas sensing.

We report on the development and validation of a compact laser instrument using mid-IR direct absorption spectroscopy (DAS) for high-precision measurements of ethanol in breath-like air mixtures. Leveraging the intermittent continuous wave (iCW) driving for conventional narrow-band distributed feedback (DFB) quantum cascade laser (QCL) emitting around 9.3 µm and using a 25 m path length multiple-pass absorption cell at reduced pressure, a precision of 9 ppb (amount fraction, nmol mol −1) at 60 s integration time is achieved even in the presence of 5% of H 2 O and CO 2. Thus, the instrument is well suitable for metrological studies to investigate observed, but yet unquantified, discrepancies between different breath alcohol reference-generation methods. The approach can be generalized and applied for other organic molecules in a wide range of applications.

Abstract. A Zeppelin airship was used as a platform for in situ measurements of greenhouse gases and short-lived air pollutants within the planetary boundary layer (PBL) in Germany. A novel quantum cascade laser-based multi-compound gas analyzer (MIRO Analytical AG) was deployed to simultaneously measure in situ concentrations of greenhouse gases (CO2, N2O, H2O, and CH4) and air pollutants (CO, NO, NO2, O3, SO2, and NH3) with high precision at a measurement rate of 1 Hz. These measurements were complemented by electrochemical sensors for NO, NO2, Ox (NO2 + O3), and CO, an optical particle counter, temperature, humidity, altitude, and position monitoring. Instruments were operated remotely without the need for on-site interactions. Three 2-week campaigns were conducted in 2020 comprising commercial passenger as well as targeted flights over multiple German cities including Cologne, Mönchengladbach, Düsseldorf, Aachen, Frankfurt, but also over industrial areas and highways. Vertical profiles of trace gases were obtained during the airship landing and take-off. Diurnal variability of the Zeppelin vertical profiles was compared to measurements from ground-based monitoring stations with a focus on nitrogen oxides and ozone. We find that their variability can be explained by the increasing nocturnal boundary layer height from early morning towards midday, an increase in emissions during rush hour traffic, and the rapid photochemical activity midday. Higher altitude (250–450 m) NOx to CO ratios are further compared to the 2015 EDGAR emission inventory to find that pollutant concentrations are influenced by transportation and residential emissions as well as manufacturing industries and construction activity. Finally, we report NOx and CO concentrations from one plume transect originating from a coal power plant and compare it to the EURopean Air pollution Dispersion-Inverse Modell (EURAD-IM) model to find agreement within 15 %. However, due to the increased contribution of solar and wind energy and the impact of lockdown measures the power plant was operating at max. 50 % capacity; therefore, possible overestimation of emissions by the model cannot be excluded.