In recent years, alloy and alloy-ceramic coatings have gained a considerable attention owing to their favorable physicochemical and technological properties. In this review, we investigate Ni, NiCo alloy and NiCo–ceramic composite coatings prepared by electrodeposition. Electrodeposition is a versatile tool and cost-effective electrochemical method used to produce high quality metal coatings. Surface finish and tribological properties of the coatings can be further improved by the addition of suitable agents and control of deposition operating conditions. In this review, Ni, NiCo alloy and NiCo–ceramic composite coatings prepared by electrodeposition are reviewed by critically evaluating previous researches. The use of the coatings and their potential for future research and development are discussed.
Ni–W/Cr2O3 nanocomposite coatings were synthesized from aqueous sulphate-citrate electrolyte containing Cr2O3 nanoparticles on a steel surface using conventional electrodeposition technique. This study was aimed at investigating the influence of Cr2O3 nanoparticle content on the microstructure, corrosion resistance, and mechanical properties of electrodeposited Ni–W/Cr2O3 nanocomposite coatings. Ni–W binary alloy coatings were deposited and optimized before addition of the nanoparticles to produce high-quality coatings. The microstructure and chemical composition of the Ni–W/Cr2O3 nanocomposite coatings were evaluated using scanning electron microscope (SEM), energy dispersive X-ray spectrometer (EDS), and XRD. Corrosion resistance properties were evaluated using potentiodynamic polarization (Tafel) measurements in 3.5 wt.% NaCl medium. The corrosion resistance and microhardness are significantly higher in Ni–W/Cr2O3 nanocomposite coatings compared to pure Ni–W binary alloy and increase with the increase in content of Cr2O3 nanoparticles in the coatings. Wear resistance is also higher in Ni–W/Cr2O3 nanocomposite coatings.
High velocity arc spraying was used to prepare FeCrAl/Al composite coating on Q235 steel substrate by simultaneously spraying FeCrAl wire as the anode and Al wire as the cathode. The composite coating was sprayed with varying voltage and current to obtain optimum coating characteristics. FeCrAl coating was also prepared for comparison purposes. The surface microstructure of the coatings was characterized by scanning electron microscope (SEM) and X-ray diffraction (XRD). The average microhardness of the coatings and the substrate was analyzed and compared. Corrosion resistance was investigated by means of electrochemical tests. The image results showed that a lamellar structure consisted of interwoven layers of FeCrAl and Al. Al and FeCr constituted the main phases with traces of oxides and AlFe intermetallic compounds. The average porosity was reduced and microhardness of the coatings was improved with increasing voltage and current. The FeCrAl/Al coating formed alternating layers of hard and ductile phases; the corrosion resistance of the coatings in the sodium chloride (NaCl) solution depended on the increase in Al content and spray parameters. The corrosion resistance tests indicated that FeCrAl/Al coating had a better corrosion resistance than the FeCrAl coating. FeCrAl/Al can be used to coat steel substrates and increase their corrosion resistance.
Inspired by natural creatures, superhydrophobic surfaces with various adhesion behaviors have attracted significant scientific interest. In this study, by controlling the laser fluence, the scanning times, and the subsequent cleaning method, microcolumn arrays with different morphologies were fabricated on 304 stainless-steel surfaces using picosecond laser direct writing. To achieve wettability transition, the laser-processed samples were then subjected to heat treatments (120 °C) in air and in a low vacuum environment (6 kPa). The results show that after heat treatment in different environments and with various time lengths, the laser-processed surfaces become hydrophobic surfaces with different adhesion properties. It is worth noting that while surfaces heat-treated in air exhibit weak wettability transition potential and high adhesion, the surfaces heat-treated in a low vacuum environment present superhydrophobic and low adhesion properties with a minimum sliding angle of about 3.14°. Moreover, the low-vacuum heat-treated surfaces retain good superhydrophobic properties after 1 month of observation as well as an abrasion test. These transitions in hydrophobic behavior and adhesion properties may be mainly attributed to the heat treatment-induced (in the air or in a low vacuum environment) redistribution of surface compounds and the microstructure-induced alternation of the solid–liquid contact state. By controlling the laser processing parameters and the heat treatment time and environment, stable wettability transition and flexible adhesion control of stainless steel can be easily achieved.
In this study, a grit-blasting pretreatment was used to improve the adhesion, corrosion resistance and microhardness of Ni-W/SiC nanocomposite coatings fabricated using the conventional electrodeposition technique. Prior to deposition, grit blasting and polishing (more commonly used) pretreatments were used to prepare the surface of the substrate and the 3D morphology of the pretreated substrates was characterized using laser scanning confocal microscopy. The coating surface and the cross-section morphology were analyzed using scanning electron microscopy (SEM). The chemical composition, crystalline structure, microhardness, adhesion and corrosion behavior of the deposited coatings were characterized using energy-dispersive spectroscopy (EDS), X-ray diffraction (XRD), a microhardness tester, a scratch tester and an electrochemical workstation, respectively. The results indicated that the grit blasting and SiC addition improved the microhardness, adhesion and corrosion resistance. The Ni-W/SiC nanocomposites pretreated by grit blasting exhibited the best adhesion strength, up to 36.5 ± 0.75 N. Its hardness was the highest and increased up to 673 ± 5.47 Hv and its corrosion resistance was the highest compared to the one pretreated by polishing.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.