Although there exist numerous established laboratory-based technologies for sample diagnostics and analyte detection, many medical and forensic science applications require point of care based platforms for rapid on-the-spot sample analysis. Electrochemical biosensors provide a promising avenue for such applications due to the portability and functional simplicity of the technology. However, the ability to develop such platforms with the high sensitivity and selectivity required for analysis of low analyte concentrations in complex biological samples remains a paramount issue in the field of biosensing. Nonspecific adsorption, or fouling, at the electrode interface via the innumerable biomolecules present in these sample types (i.e., serum, urine, blood/plasma, and saliva) can drastically obstruct electrochemical performance, increasing background "noise" and diminishing both the electrochemical signal magnitude and specificity of the biosensor. Consequently, this review aims to discuss strategies and concepts used throughout the literature to prevent electrode surface fouling in biosensors and to communicate the nature of the antifouling mechanisms by which they operate. Evaluation of each antifouling strategy is focused primarily on the fabrication method, experimental technique, sample composition, and electrochemical performance of each technology highlighting the overall feasibility of the platform for point of care based diagnostic/detection applications.

Preventing the unwanted adsorption of proteins and cells at articular cartilage surfaces plays a critical role in maintaining healthy joints and avoiding degenerative diseases such as osteoarthritis. Immobilized at the surface of healthy articular cartilage is a thin, interfacial layer of macromolecules consisting mainly of hyaluronic acid (HA) and lubricin (LUB; a.k.a. PRG4) that is believed to form a co-adsorbed, composite film now known to exhibit synergistic tribological properties. Bioinspired by the composition of cartilage surfaces, composite layers of HA and LUB were grafted to Au surfaces and the antiadhesive properties were assessed using surface plasmon resonance and quartz crystal microbalance. A clear synergistic enhancement in antiadhesive properties was observed in the composite films relative to grafted HA and LUB layers alone. Atomic force microscopy (AFM) normal force measurements provide insight into the architecture of the HA/LUB composite layer and implicate a strong contribution of hydrophobic interactions in the binding of LUB end-domains directly to HA chains. These AFM force measurements indicate that the adhesion of LUB to HA is strong and indicate that the hydrophobic coupling of LUB to HA shields the hydrophobic domains in these molecules from interactions with other proteins or molecules.

No abstract

Lubricin (LUB, aka PRG4), a mucin-like glycoprotein, is best known for the significant role it plays in the boundary lubrication, wear protection, and adhesion control systems in human joints. However, LUB exhibits a number of diverse and useful properties, including a remarkable ability to self-assemble into a telechelic brush structure onto virtually any substrate. This self-assembly behavior has spawned the emergence of numerous nontraditional applications of LUB coatings in numerous areas such as microfluidics, electrochemical sensors, contact lenses, antifouling surfaces, and bionic neural interfaces. Although LUB will readily self-assemble on most substrates, it has become apparent that the substrate has a significant influence on the LUB layer’s demonstrated lubrication, antiadhesion, electrokinetic, and size-selective transport properties; however, investigations into LUB–substrate interactions and how they influence the self-assembled LUB layer structure remain a neglected aspect of LUB research. This study utilizes AFM force spectroscopy to directly assess the adhesion energy of LUB molecules adsorbed to a wide variety of different substrates which include inorganic, polymeric, and metallic materials. An analysis of the steric repulsive forces measured on approach provides a qualitative assessment of the LUB layer’s mechanical modulus, related to the chain packing density, across substrates. These modulus measurements, combined with characteristic features and the dwell time dependence of the LUB adhesion forces provide insight into the organization and uniformity of the LUB brush structure. The results of these measurements indicate that LUB interactions with different substrates are highly variable and substrate-specific, resulting in a surprisingly broad spectrum of adhesion energies and layer properties (i.e., chain density, uniformity, etc.) which are not, themselves, correlated or easily predicted by substrate properties. In addition, this study finds exceptionally poor LUB adhesion to both mica and poly­(methyl methacrylate) surfaces that remain widely used substrates for constructing model surfaces in fundamental tribology studies which may have significant implications for the findings of a number of foundational studies into LUB tribology and molecular synergies.