In general, standard aerodynamic design is divided into two paths—numerical analysis and empirical tests. It is crucial to efficiently combine both approaches in order to entirely fulfill the requirements of the design process as well as the final product. An effective use of computational analysis is a challenge, however it can significantly improve understanding, exploring and confining the search for optimal product solutions. The article focuses on a rapid prototyping and testing procedure proposed and employed at the Institute of Turbomachinery, Lodz University of Technology (IMP TUL). This so called Fast Track approach combines preparation of numerical models of a wind turbine rotor, manufacturing of its geometry by means of a 3D printing method and testing it in an in-house wind tunnel. The idea is to perform the entire procedure in 24 h. The proposed process allows one to determine the most auspicious sets of rotor blades within a short time. Owing to this, it significantly reduces the amount of individual subsequent examinations. Having fixed the initial procedure, it is possible to expand research on the singled-out geometries. The abovementioned observations and the presented overview of the literature on uses of 3D printing in aerodynamic testing prove rapid prototyping as an innovative and widely-applicable method, significantly changing our approach to experimental aerodynamics.
Purpose This paper aims to discuss the results of the performance study of wind turbine blades equipped with winglets. An investigation focusses on small wind turbines (SWTs), where the winglets are recalled as one of the most promising concepts in terms of turbine efficiency increase. Design/methodology/approach To investigate a contribution of winglets to SWT aerodynamic efficiency, a wind tunnel experiment was performed at Lodz University of Technology. In parallel, computational fluid dynamics (CFD) simulations campaign was conducted with the ANSYS CFX software to investigate appearing flow structures in greater detail. Findings The research indicates the potential behind the application of winglets in low Reynolds flow conditions, while the CFD study enables the identification of crucial regions influencing the flow structure in the most significant degree. Research limitations/implications As the global effect on a whole rotor is a result of a small-scale geometrical feature, it is important to localise unveiled phenomena and the mechanisms behind their generation. Practical implications Even the slightest efficiency improvement in a distributed generation installation can promote such a solution amongst energy prosumers and increase their independence from limited natural resources. Originality/value The winglet-equipped blades of SWTs provide an opportunity to increase the device performance with relatively low cost and ease of implementation.
Purpose This paper aims to provide the results of investigations concerning an influence of the tyre with longitudinal grooves on the car body aerodynamics. It is considered as an important aspect affecting the vehicle aerodynamic drag. Design/methodology/approach To investigate a contribution of grooved tyres to the overall vehicle drag, three wind tunnel experimental campaigns were performed (two by Peugeot Société Anonyme Peugeot Citroen, one at the Lodz University of Technology). In parallel, computational fluid dynamics (CFD) simulations were conducted with the ANSYS CFX software to enable formulation of wider conclusions. Findings The research shows that optimised tread patterns can be derived on a single tyre via a CFD study in combination with a controlled experiment to deliver designs actively lowering the overall vehicle aerodynamic drag. Practical implications A reduction in the aerodynamic drag is one of ways to decrease vehicle fuel consumption. Alternatively, it can be translated into an increase in the maximum travel velocity and the maximum distance driven (key factor in electric vehicles), as well as in a reduction of CO2 emissions. Finally, it can improve the vehicle driving and steering stability. Originality/value The tyre tread pattern analysis on isolated wheels provides an opportunity to cut costs of R&D and could be a step towards isolating aerodynamic properties of tyres, irrespective of the car body on which they are applied.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.