O objetivo deste estudo foi avaliar a viabilidade da utilização de lignosulfonato de cálcio e magnésio (LS) na produção de painéis aglomerados de Pinus caribaea var. caribaea, na forma pura e em misturas com fenol-formaldeído (FF). De modo a avaliar o efeito da substituição de FF por LS sobre as propriedades físicas e mecânicas, foram produzidos painéis com diferentes concentrações desses adesivos. O delineamento experimental foi constituído de duas fases. A primeira fase foi realizada sob a temperatura de 160°C e tempo de prensagem de 10 minutos, com as seguintes composições: 100% de FF, e as substituições por LS nas proporções de 20, 40, 60, 80 e 100%, com três repetições cada. Na segunda fase, os três tratamentos da primeira fase com desempenho inferior nas propriedades mecânicas foram testados na temperatura de 180°C em tempos de prensagem de 5 e 7 minutos. Os resultados médios da densidade básica e aparente da madeira foram de 0,54 e 0,60g/cm³, respectivamente. Na segunda fase, o aumento da temperatura e a diminuição do tempo de prensagem não foram suficientes para consolidar o painel, não sendo possível analisar os resultados desta fase. Com relação ao inchamento em espessura e absorção de água, à medida que aumentou a proporção de lignosulfonato na mistura elevaram-se também esses valores. Em até 80%, a substituição do adesivo fenol-formaldeído por lignosulfonato foi satisfatória no atendimento a NBR 14810-2 (ABNT,2013) para propriedades mecânicas. O lignosulfonato apresentou eficiência na utilização como adesivo na produção de painéis aglomerados em misturas com fenol-formaldeído, evidenciando que esta é uma alternativa à utilização de adesivos sintéticos.
O presente trabalho teve o objetivo de comparar o comportamento de cinco espécies nativas brasileiras: Angelim (Andira anthelmia), canela (Anila firmula), cedro (Cedrela fissilis), ipê amarelo (Tabebuia alba) e muiracatiara (Astronium lecointein) através de ensaios de usinagem. Confeccionaram-se dez amostras para cada espécie de dimensões, seguindo a norma americana ASTM D-1666-87 e determinou-se, ainda, a densidade aparente da madeira (g.cm-3) com base na NBR 7190, a fim de estabelecer possíveis relações. Os ensaios de usinagem realizados foram: teste de plaina, furo para dobradiça e para cavilha, teste de rasgo, de lixa, fendilhamento por pregos e ensaio de torneamento. Todas as espécies avaliadas se comportaram bem com relação ao teste de lixa e furação para cavilha, não apresentando diferenças significativas entre as notas obtidas. Porém, o ipê apresentou o pior resultado para o ensaio de plaina, e o cedro, devido a sua menor densidade aparente, obteve o pior resultado frente aos ensaios de furação. Com relação ao ensaio de torneamento, as espécies de ipê e canela foram classificadas como as melhores dentre as espécies avaliadas. De forma geral, pôde-se concluir que as espécies apresentaram potenciais de usos em móveis, esquadrias e ocasiões de acabamento gerais.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.