Underwater remotely operated vehicles (ROVs) play an important role in a number of shallow and deepwater missions for marine science, oil and gas extraction, exploration and salvage. In these applications, the motions of the ROV are guided either by a human pilot on a surface support vessel through an umbilical cord providing power and telemetry, or by an automatic pilot. In the case of automatic control, ROV state feedback is provided by acoustic and inertial sensors and this state information, along with a controller strategy, is used to perform several tasks such as station-keeping and autoimmersion/heading, among others. In this paper, the modelling, design and control of the Kaxan ROV is presented: i) The complete six degrees of freedom, non linear hydrodynamic model with its parameters, ii) the Kaxan hardware/software architecture, iii) numerical simulations in Matlab/Simulink platform of a model-free second order sliding mode control along with ocean currents as disturbances and thruster dynamics, iv) a virtual environment to visualize the motion of the Kaxan ROV and v) experimental results of a one degree of freedom underwater system.
This article investigates visual servoing for a hydraulically actuated dual-arm robot, in which the user selects the object of interest from an on-screen image, whilst the computer control system implements via feedback control the required position and orientation of the manipulators.To improve on the current joystick direct tele-operation commonly used as standard in the nuclear industry, which is slow and requires extensive operator training, the proposed assisted tele-operation makes use of a single camera mounted on the robot. Focusing on pipe cutting as an example, the new system ensures that one manipulator automatically grasps the user-selected pipe, and appropriately positions the second for a cutting operation. Initial laboratory testing (using a plastic pipe) shows the efficacy of the approach for positioning the manipulators, and suggests that for both experienced and inexperienced users, the task is completed significantly faster than via tele-operation.
This paper presents algorithms implemented for positioning a wheeled robot on a production floor inside a factory by means of radio-frequency distance measurement and trilateration techniques. A set of radio-frequency transceivers located on the columns of the factory (anchors) create a grid with several triangular zones capable of measuring the line-of-sight distance between each anchor and the transceiver installed in the wheeled robot. After measuring only three of these distances (radii), an enhanced trilateration algorithm is applied to obtain X and Y coordinates in a Cartesian plane, i.e., the position of the robot on the factory floor. The embedded systems developed for the anchors and the robot are robust enough to establish communication, select the closest anchors for measuring radii, and identify in which of the grid zones the robot is located.
Torque ripple occurs in Permanent Magnet Synchronous Motors (PMSMs) due to the non-sinusoidal flux density distribution around the air-gap and variable magnetic reluctance of the air-gap due to the stator slots distribution. These torque ripples change periodically with rotor position and are apparent as speed variations, which degrade the PMSM drive performance, particularly at low speeds, because of low inertial filtering. In this paper, a new self-tuning algorithm is developed for determining the Fourier Series Controller coefficients with the aim of reducing the torque ripple in a PMSM, thus allowing for a smoother operation. This algorithm adjusts the controller parameters based on the component's harmonic distortion in time domain of the compensation signal. Experimental evaluation is performed on a DSP-controlled PMSM evaluation platform. Test results obtained validate the effectiveness of the proposed self-tuning algorithm, with the Fourier series expansion scheme, in reducing the torque ripple.
This paper describes both the design and technical integration of a deep water ROV (Remotely Operated Vehicle) that is able to employ visual inspection in deep water, as well as to take samples with an underwater arm. Visual inspection is the essential application for a ROV, which is useful for; underwater structure inspection, underwater oil production systems inspection and underwater pipeline inspection. This paper mainly describes the ROV design, and explains in general manner other elements; such as the SCU, LARS and TMS. It is important to mention that the design phase is complete and it was financed by PEMEX (Federal Mexican Oil Company). The project has stalled, since we are waiting for the financial support from PEMEX for the system construction. A future objective is the design and construction of Work-Class ROVs, which can be used to perform PEMEX specific tasks.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.