The X-ray absorption spectra (XAS) of lithium polysulfides (Li2Sx) of various chain lengths (x) dissolved in a model solvent are obtained from first-principles calculations. The spectra exhibit two main absorption features near the sulfur K-edge, which are unambiguously interpreted as a pre-edge near 2471 eV due to the terminal sulfur atoms at either end of the linear polysulfide dianions and a main-edge near 2473 eV due to the (x - 2) internal atoms in the chain, except in the case of Li2S2, which only has a low-energy feature. We find an almost linear dependence between the ratio of the peaks and chain length, although the linear dependence is modified by the delocalized, molecular nature of the core-excited states that can span up to six neighboring sulfur atoms. Thus, our results indicate that the ratio of the peak area, and not the peak intensities, should be used when attempting to differentiate the polysulfides from XAS.

The presence and role of polysulfide radicals in the electrochemical processes of lithium sulfur (Li–S) batteries is currently being debated. Here, first‐principles interpretations of measured X‐ray absorption spectra (XAS) of Li–S cells are leveraged with an ether‐based electrolyte. Unambiguous evidence is found for significant quantities of polysulfide radical species (LiS3, LiS4, and LiS5), including the trisulfur radical anion S3 −, present after initial discharge to the first discharge plateau, as evidenced by a low energy shoulder in the S K‐edge XAS below 2469 eV. This feature is not present in the XAS of cells at increased depth of discharge, which, by our analysis, exhibit increasing concentrations of progressively shorter polysulfide dianions. Through a combination of first‐principles molecular dynamics and associated interpretation of in situ XAS of Li–S cells, atomic level insights into the chemistries are provided that underlie the operation and stability of these batteries.

Lithium-sulfur batteries have a theoretical specific energy that is a factor of five greater than that of current lithium-ion batteries, but suffer from consequences of the solubility of lithium polysulfide reaction intermediates that form as the batteries are charged and discharged. These species can react with each other and diffuse out of the cathode, causing battery capacity to fade and ultimately, cell failure. In spite of work that has spanned four decades, "fingerprints" of polysulfides have not yet been established, precluding a systematic study of lithium-sulfur chemistry. Herein we demonstrate the use of principal component analysis of X-ray absorption spectroscopy (XAS) to obtain fingerprints of lithium polysulfides. This approach enables interpretation of spectral data without any assumptions regarding the origin of the observed spectral features or knowledge of the stability of the polysulfide species of interest. We show that in poly(ethylene oxide)-based solid electrolytes containing polysulfides made by chemically reacting Li 2 S and elemental sulfur, Li 2 S 2 and Li 2 S 6 spontaneously disproportionate to give binary Li 2 S/Li 2 S 4 and Li 2 S 4 /Li 2 S 8 mixtures, respectively, while Li 2 S 4 and Li 2 S 8 exist as single molecular species. XAS fingerprints of Li 2 S 4 and Li 2 S 8 are thus presented.

Despite high ionic conductivities, current inorganic solid electrolytes cannot be used in lithium batteries because of a lack of compliance and adhesion to active particles in battery electrodes as they are discharged and charged. We have successfully developed a compliant, nonflammable, hybrid single ion-conducting electrolyte comprising inorganic sulfide glass particles covalently bonded to a perfluoropolyether polymer. The hybrid with 23 wt% perfluoropolyether exhibits low shear modulus relative to neat glass electrolytes, ionic conductivity of 10 −4 S/cm at room temperature, a cation transference number close to unity, and an electrochemical stability window up to 5 V relative to Li + /Li. X-ray absorption spectroscopy indicates that the hybrid electrolyte limits lithium polysulfide dissolution and is, thus, ideally suited for Li-S cells. Our work opens a previously unidentified route for developing compliant solid electrolytes that will address the challenges of lithium batteries.hybrid electrolytes | inorganic sulfide glasses | fluorinated polymers | lithium batteries | lithium-sulfur batteries E lectrolytes used in lithium ion batteries that power personal electronic devices and electric vehicles comprise lithium salts dissolved in flammable organic liquids. Catastrophic battery failure often begins with the electrolyte decomposition and combustion. In addition, side reactions between the electrolyte and anode particles result in steady capacity fade. Some of the byproducts of side reactions can dissolve in the electrolyte and migrate from one electrode to the other. This effect is minimized in the case of solid electrolytes because of limited solubility and slow diffusion (1). Mixtures of liquids and salts have additional limitations. The passage of current results in an accumulation of salt in the vicinity of one electrode and depletion close to the other electrode, because only the cation participates in the electrochemical reactions. Both overconcentrated and depleted electrolytes have lower conductivity, which accentuates cell polarization and reduces power capability. Concentration polarization is absent in single-ion conductors, wherein the anions are immobilized (2). Nonflammable, single ionconducting solid electrolytes have the potential to dramatically improve safety and performance of lithium batteries (3-6).Solid electrolytes, such as inorganic sulfide glasses (Li 2 S-P 2 S 5 ), are single-ion conductors with high shear moduli (18-25 GPa) and high ionic conductivity (over 10 −4 S/cm) at room temperature (7,8). However, these materials, on their own, cannot serve as efficient electrolytes, because they cannot adhere to moving boundaries of the active particles in the battery electrode as they are charged and discharged. Hayashi et al. (9) prepared hybrid electrolytes by mixing sulfide glasses and poly(ethylene oxide) (PEO) polymers. Although the addition of PEO improves mechanical flexibility, there is a dramatic decrease in ionic conductivity because of the insulative nature of PEO. For exampl...