Rubidium (Rb) is explored as an alternative cation to use in a novel multication method with the formamidinium/methylammonium/cesium (Cs) system to obtain 1.73 eV bangap perovskite cells with negligible hysteresis and steady state efficiency as high as 17.4%. The study shows the beneficial effect of Rb in improving the crystallinity and suppressing defect migration in the perovskite material. The light stability of the cells examined under continuous illumination of 12 h is improved upon the addition of Cs and Rb. After several cycles of 12 h light–dark, the cell retains 90% of its initial efficiency. In parallel, sputtered transparent conducting oxide thin films are developed to be used as both rear and front transparent contacts on quartz substrate with less than 5% parasitic absorption of near infrared wavelengths. Using these developments, semi‐transparent perovskite cells are fabricated with steady state efficiency of up to 16.0% and excellent average transparency of ≈84% between 720 and 1100 nm. In a tandem configuration using a 23.9% silicon cell, 26.4% efficiency (10.4% from the silicon cell) in a mechanically stacked tandem configuration is demonstrated which is very close to the current record for a single junction silicon cell of 26.6%.

The interdigitated back contact (IBC) solar cells developed at the Australian National University have resulted in an independently confirmed (Fraunhofer Institut für Solare Energiesysteme (ISE) CalLab) designated‐area efficiency of 24.4 ± 0.7%, featuring short‐circuit current density of 41.95 mA/cm2, open‐circuit voltage of 703 mV and 82.7% fill factor. The cell, 2 × 2 cm2 in area, was fabricated on a 230 µm thick 1.5 Ω cm n‐type Czochralski wafer, utilising plasma‐enhanced chemical vapour deposition (CVD) SiNx front‐surface passivation without front‐surface diffusion, rear‐side thermal oxide/low‐pressure CVD Si3N4 passivation stack and evaporated aluminium contacts with a finger‐to‐finger pitch of 500 µm. This paper describes the design and fabrication of lab‐scale high‐efficiency IBC cells. Characterisation of optical and electronic properties of the best produced cell is made, with subsequent incorporation into 3D device modelling used to accurately quantify all losses. Loss analysis demonstrates that bulk and emitter recombination, bulk resistive and optical losses are dominant and suggests a clear route to efficiency values in excess of 25%. Additionally, laser processing is explored as a means to simplify the manufacture of IBC cells, with a confirmed efficiency value of 23.5% recorded for cells fabricated using damage‐free deep UV laser ablation for contact formation. Meanwhile all‐laser‐doped cells, where every doping and patterning step is performed by lasers, are demonstrated with a preliminary result of 19.1% conversion efficiency recorded. Copyright © 2014 John Wiley & Sons, Ltd.

The article commences with a review focusing on three critical aspects of the perovskite/Si tandem technology: the evolution of efficiencies to date, comparisons of Si subcell choices, and the interconnection design strategies. Building on this review, a clear route is provided for minimizing optical losses aided by optical simulations of a recently reported high‐efficiency perovskite/Si tandem system, optimizations which result in tandem current densities of ≈20 mAcm−2 with front‐side texture. The primary focus is on electrical modeling on the Si‐subcell, in order to understand the efficiency potential of this cell under filtered light in a tandem configuration. The possibility of increasing the Si subcell efficiency by 1% absolute is offered through joint improvements to the bulk lifetime, which exceeds 4 ms, and improves surface passivation quality to saturation current densities below 10 fA cm−2. Polycrystalline‐Si/SiOx passivating contacts are proposed as a promising alternative to partial‐area rear contacts, with the potential for further simplifying cell fabrication and improving device performance. A combination of optical modeling of the complete tandem structure alongside electrical modeling of the Si‐subcell, both with state‐of‐the‐art modeling tools, provides the first complete picture of the practical efficiency potential of perovskite/Si tandems.

Within the silicon photovoltaics (PV) community, there are many approaches, tools, and input parameters for simulating solar cells, making it difficult for newcomers to establish a complete and representative starting point and imposing high requirements on experts to tediously state all assumptions and inputs for replication. In this review, we address these problems by providing complete and representative input parameter sets to simulate six major types of crystalline silicon solar cells. Where possible, the inputs are justified and up-to-date for the respective cell types, and they produce representative measurable cell characteristics. Details of the modeling approaches that can replicate the simulations are presented as well. The input parameters listed here provide a sensible and consistent reference point for researchers on which to base their refinements and extensions.

Mixed‐dimensional perovskite solar cells combining 3D and 2D perovskites have recently attracted wide interest owing to improved device efficiency and stability. Yet, it remains unclear which method of combining 3D and 2D perovskites works best to obtain a mixed‐dimensional system with the advantages of both types. To address this, different strategies of combining 2D perovskites with a 3D perovskite are investigated, namely surface coating and bulk incorporation. It is found that through surface coating with different aliphatic alkylammonium bulky cations, a Ruddlesden–Popper “quasi‐2D” perovskite phase is formed on the surface of the 3D perovskite that passivates the surface defects and significantly improves the device performance. In contrast, incorporating those bulky cations into the bulk induces the formation of the pure 2D perovskite phase throughout the bulk of the 3D perovskite, which negatively affects the crystallinity and electronic structure of the 3D perovskite framework and reduces the device performance. Using the surface‐coating strategy with n‐butylammonium bromide to fabricate semitransparent perovskite cells and combining with silicon cells in four‐terminal tandem configuration, 27.7% tandem efficiency with interdigitated back contact silicon bottom cells (size‐unmatched) and 26.2% with passivated emitter with rear locally diffused silicon bottom cells is achieved in a 1 cm2 size‐matched tandem.