It is generally believed that the strength of the polymer-nanoparticle interaction controls the modification of near-interface segmental mobility in polymer nanocomposites (PNCs). However, little is known about the effect of covalent bonding on the segmental dynamics and glass transition of matrix-free polymer-grafted nanoparticles (PGNs), especially when compared to PNCs. In this article, we directly compare the static and dynamic properties of poly(2-vinylpyridine)/silica-based nanocomposites with polymer chains either physically adsorbed (PNCs) or covalently bonded (PGNs) to identical silica nanoparticles (RNP = 12.5 nm) for three different molecular weight (MW) systems. Interestingly, when the MW of the matrix is as low as 6 kg/mol (RNP/Rg = 5.4) or as high as 140 kg/mol (RNP/Rg= 1.13), both small-angle X-ray scattering and broadband dielectric spectroscopy show similar static and dynamic properties for PNCs and PGNs. However, for the intermediate MW of 18 kg/mol (RNP/Rg = 3.16), the difference between physical adsorption and covalent bonding can be clearly identified in the static and dynamic properties of the interfacial layer. We ascribe the differences in the interfacial properties of PNCs and PGNs to changes in chain stretching, as quantified by self-consistent field theory calculations. These results demonstrate that the dynamic suppression at the interface is affected by the chain stretching; that is, it depends on the anisotropy of the segmental conformations, more so than the strength of the interaction, which suggests that the interfacial dynamics can be effectively tuned by the degree of stretching-a parameter accessible from the MW or grafting density.

Starting from a coarse grained representation of the building units of the minute virus of mice and a flexible polyelectrolyte molecule, we have explored the mechanism of assembly into icosahedral structures with the help of Langevin dynamics simulations and the parallel tempering technique. Regular icosahedra with appropriate symmetry form only in a narrow range of temperature and polymer length. Within this region of parameters where successful assembly would proceed, we have systematically investigated the growth kinetics. The assembly of icosahedra is found to follow the classical nucleation and growth mechanism in the absence of the polymer, with the three regimes of nucleation, linear growth, and slowing down in the later stage. The calculated average nucleation time obeys the laws expected from the classical nucleation theory. The linear growth rate is found to obey the laws of secondary nucleation as in the case of lamellar growth in polymer crystallization. The same mechanism is seen in the simulations of the assembly of icosahedra in the presence of the polymer as well. The polymer reduces the nucleation barrier significantly by enhancing the local concentration of subunits via adsorbing them on their backbone. The details of growth in the presence of the polymer are also found to be consistent with the classical nucleation theory, despite the smallness of the assembled structures.

The composition of polymer blends near interfaces can differ from the average blend composition because the attraction of each polymer toward surfaces is controlled by its chemistry, size, and architecture. In this work, we studied thin film blends of bottlebrush copolymers and linear homopolymers to understand the enthalpic and entropic effects that drive preferential segregation of one constituent to film interfaces. Bottlebrush copolymers containing polystyrene (PS) and poly­(methyl methacrylate) (PMMA) side chains were blended with either linear PS or linear PMMA, and time-of-flight secondary ion mass spectroscopy was used to quantify the distribution of bottlebrushes through the film thickness as a function of homopolymer type, homopolymer molecular weight, and processing conditions. We found that the bottlebrush copolymers segregated to air and substrate interfaces above a critical molecular weight of the linear homopolymer, consistent with an entropic preference for chain ends and shorter chains toward the interfaces. This segregation was used to tailor the surface wettability of blend films using bottlebrush additives as a minority component. Modeling using self-consistent field theory highlighted effects of conformational entropy and enthalpic interactions in driving almost complete segregation from the interior of the films toward interfaces. Furthermore, enthalpic interactions were predicted to cause lateral phase segregation in cases where the homopolymer is preferred over the bottlebrush copolymer at the substrate, an effect that was also observed in experiments. This study demonstrates that bottlebrush copolymer additives can be designed to spontaneously segregate to surfaces in thermal blends, providing a possible route to decouple surface properties from bulk properties.