No abstract

Carbon-based materials are considered to be active for electrochemical oxygen reduction reaction (ORR) to hydrogen peroxide (H2O2) production. Nevertheless, less attention is paid to the investigation of the influence of in-plane carbon lattice defect on the catalytic activity and selectivity toward ORR. In the present work, graphene precursors were prepared from oxo-functionalized graphene (oxo-G) and graphene oxide (GO) with H2O2 hydrothermal treatment, respectively. Statistical Raman spectroscopy (SRS) analysis demonstrated the increased in-plane carbon lattice defect density in the order of oxo-G, oxo-G/H2O2, GO, GO/H2O2. Furthermore, nitrogen-doped graphene materials were prepared through ammonium hydroxide hydrothermal treatment of those graphene precursors. Rotating ring-disk electrode (RRDE) results indicate that the nitrogen-doped graphene derived from oxo-G with lowest in-plane carbon lattice defects exhibited the highest H2O2 selectivity of >82% in 0.1 M KOH. Moreover, a high H2O2 production rate of 224.8 mmol gcatalyst –1 h–1 could be achieved at 0.2 VRHE in H-cell with faradaic efficiency of >43.6%. Our work provides insights for the design and synthesis of carbon-based electrocatalysts for H2O2 production.

Significant reduction of the precious metal catalyst loading is one of the key challenges for the commercialization of proton-exchange membrane water electrolyzers. In this work we combine IrOx nanofibers with a conventional nanoparticle-based IrOx anode catalyst layer. With this hybrid design we can reduce the iridium loading by more than 80% while maintaining performance. In spite of an ultralow overall catalyst loading of 0.2 mgIr/cm2, a cell with a hybrid layer shows similar performance compared to a state-of-the-art cell with a catalyst loading of 1.2 mgIr/cm2 and clearly outperforms identically loaded reference cells with pure IrOx nanoparticle and pure nanofiber anodes. The improved performance is attributed to a combination of good electric contact and high porosity of the IrOx nanofibers with high surface area of the IrOx nanoparticles. Besides the improved performance, the hybrid layer also shows better stability in a potential cycling and a 150 h constant current test compared to an identically loaded nanoparticle reference.

Cathode catalyst layers of proton exchange membrane fuel cells (PEMFCs) typically consist of carbon-supported platinum catalysts with varying weight ratios of proton-conducting ionomers. N-Doping of carbon support materials is proposed to enhance the performance and durability of the cathode layer under operating conditions in a PEMFC. However, a detailed understanding of the contributing N-moieties is missing. Here, we report the successful synthesis and fuel cell implementation of Pt electrocatalysts supported on N-doped carbons, with a focus on the analysis of the N-induced effect on catalyst performance and durability. A customized fluidized bed reduction reactor was used to synthesize highly monodisperse Pt nanoparticles deposited on N-doped carbons (N−C), the catalytic oxygen reduction reaction activity and stability of which matched those of state-of-the-art PEMFC catalysts. Operando high-energy X-ray diffraction experiments were conducted using a fourth generation storage ring; the light of extreme brilliance and coherence allows investigating the impact of N-doping on the degradation behavior of the Pt/N−C catalysts. Tests in liquid electrolytes were compared with tests in membrane electrode assemblies in single-cell PEMFCs. Our analysis refines earlier views on the subject of Ndoped carbon catalyst supports: it provides evidence that heteroatom doping and thus the incorporation of defects into the carbon backbone do not mitigate the carbon corrosion during high-potential cycling (1−1.5 V) and, however, can promote the cell performance under usual PEMFC operating conditions (0.6−0.9 V).

Emulsions stabilized by solid particles are so called Pickering emulsions which are characterized by their high stability against coalescence. This type of emulsion can be used for a lot of applications. Very little is known about how reaction conditions affect their properties. In this study the influence of important reaction conditions like shear stress, pressure, temperature, and the influence of synthesis gas on Pickering emulsions is investigated. It is shown that the emulsions remain stable in terms of coalescence in a broad range of the reaction conditions and are suitable as reaction media for industrial processes and for a reaction optimization with a subsequent separation step.