Developing low-cost and biodegradable piezoelectric nanogenerators is of great importance for a variety of applications, from harvesting low-grade mechanical energy to wearable sensors. Many of the most widely used piezoelectric materials, including lead zirconate titanate (PZT), suffer from serious drawbacks such as complicated synthesis, poor mechanical properties (e.g. brittleness) and toxic composition, limiting their development for biomedical applications and posing environmental problems for their disposal. Here, we report a lowcost, biodegradable, biocompatible and highly compressible piezoelectric nanogenerator based on a wood sponge obtained with a simple delignification process. Thanks to the enhanced compressibility of the wood sponge, our wood nanogenerator (15 × 15 × 14 mm 3 , longitudinal × radial × tangential) can generate an output voltage of up to 0.69 V, 85 times higher than that generated by native (untreated) wood, and it shows stable performance under repeated cyclic compression (≥600 cycles). Our approach suggests the importance of increased compressibility of bulk materials for improving their piezoelectric output. We demonstrate the versatility of our nanogenerator by showing its application both as a wearable movement monitoring system (made with a single wood sponge) and as a large-scale prototype with increased output (made with 30 wood sponges) able to power simple electronic devices (a LED light, a LCD screen). Moreover, we demonstrate the biodegradability of our wood sponge piezoelectric nanogenerator by studying its decomposition with cellulosedegrading fungi. Our results showcase the potential application of wood sponge as a sustainable energy source, as a wearable device for monitoring human motions, and its contribution to environmental sustainability by electronic waste reduction.

Melanins are natural biopolymers that are known to contribute to different biological processes and to protect organisms from adverse environmental conditions. During the past decade, melanins have attracted increasing attention for their use in organic semiconductors and bioelectronics, drug delivery, photoprotection and environmental bioremediation. Although considerable advances in these fields have been achieved, real-world applications of melanins are still scarce, probably due to the limited and expensive source of natural melanin. Nevertheless, recent biotechnological advances have allowed for relatively large-scale production of microbial melanins, which could replace current commercial melanin. In this review, we first describe different melanin sources and highlight the advantages and disadvantages of each production method. Our focus is on the microbial synthesis of melanins, including the methodology and mechanism of melanin formation. Applications of microbial melanins are also discussed, and an outlook on how to push the field forward is discussed.

Natural melanin features many interesting properties, including the ability to shield electromagnetic radiation, the ability to act as scavenger for radical and reactive oxygen species and the capacity to chelate different metal ions. For these reasons, melanin is becoming increasingly relevant for the development of functional materials with potential applications in cosmetics, drug delivery, and water purification. However, the extraction and purification of melanin from conventional sources (e.g., sepia ink, hair, and wool) is inefficient and not easily scalable, hence diverting its technological applications. Some fungal species, especially wood-decay basidiomycetes, can be regarded as promising sources of melanin. In the present study, we screened different fungi in regard to their melanin-biosynthesis abilities using l-tyrosine as a precursor, and we found that an Armillaria cepistipes strain (Empa 655) produced the highest yield of melanin (27.98 g L–1). Physicochemical characterization of the obtained fungal melanin revealed a typical eumelanin structure. The method for the biosynthesis of fungal melanin we propose is efficient, scalable, and sustainable and has the potential to provide support for further technological exploitation.

Producing electricity from renewable sources and reducing its consumption by buildings are necessary to meet energy and climate change challenges. Wood is an excellent “green” building material and, owing to its piezoelectric behavior, could enable direct conversion of mechanical energy into electricity. Although this phenomenon has been discovered decades ago, its exploitation as an energy source has been impaired by the ultralow piezoelectric output of native wood. Here, we demonstrate that, by enhancing the elastic compressibility of balsa wood through a facile, green, and sustainable fungal decay pretreatment, the piezoelectric output is increased over 55 times. A single cube (15 mm by 15 mm by 13.2 mm) of decayed wood is able to produce a maximum voltage of 0.87 V and a current of 13.3 nA under 45-kPa stress. This study is a fundamental step to develop next-generation self-powered green building materials for future energy supply and mitigation of climate change.

Background In trees, secondary metabolites (SMs) are essential for determining the effectiveness of defence systems against fungi and why defences are sometimes breached. Using the CODIT model (Compartmentalization of Damage/Dysfunction in Trees), we explain defence processes at the cellular level. CODIT is a highly compartmented defence system that relies on the signalling, synthesis and transport of defence compounds through a three-dimensional lattice of parenchyma against the spread of decay fungi in xylem. Scope The model conceptualizes ‘walls’ that are pre-formed, formed during and formed after wounding events. For sapwood, SMs range in molecular size, which directly affects performance and the response times in which they can be produced. When triggered, high-molecular weight SMs such as suberin and lignin are synthesized slowly (phytoalexins), but can also be in place at the time of wounding (phytoanticipins). In contrast, low-molecular weight phenolic compounds such as flavonoids can be manufactured de novo (phytoalexins) rapidly in response to fungal colonization. De novo production of SMs can be regulated in response to fungal pathogenicity levels. The protective nature of heartwood is partly based on the level of accumulated antimicrobial SMs (phytoanticipins) during the transitionary stage into a normally dead substance. Effectiveness against fungal colonization in heartwood is largely determined by the genetics of the host. Conclusion Here we review recent advances in our understanding of the role of SMs in trees in the context of CODIT, with emphasis on the relationship between defence, carbohydrate availability and the hydraulic system.We also raise the limitations of the CODIT model and suggest its modification, encompassing other defence theory concepts. We envisage the development of a new defence system that is modular based and incorporates all components (and organs) of the tree from micro- to macro-scales.