This paper introduces research and development of a modern non-invasive device for determining flows and velocity fields. This device is based on the ultrasonic method. The measured fluid flow is surrounded by appropriate ultrasonic transmitters and receivers, which communicate with each other. A physical principle of this method consists in an interaction of sound waves with a flow, which generates a certain delay in sound waves transmission. The found quantity is thus time delay. The device is being designed as a flowmeter and with advanced and extended postprocessing as a tomograph, which reconstructs a 3D vector field for big volumes. This whole process requires the following: development of an appropriate design of the ultrasonic flowmeter and tomograph, testing the signal transfer and also various postprocessing methods on a measurement accuracy, building of a special verification experimental equipment and building of an electronic device as a control unit and data acquisition system.
Ultrasonic (US) flow meters are devices for a fluid flow measurement using the ultrasonic principle. Current research project dealing with developing the ultrasonic flowmeter with an innovative channel shape. Previously the work was aimed to the topology optimization using the CFD methods. The final prototype has to be analyzed experimentally to verify the velocity profiles in the US measurement section. The obtained velocity profiles in this region are necessary as the input for the US sensor data evaluation. A particle image velocimetry (PIV) was selected as a potentially suitable technique for the velocity profiles measurement. This paper presents the development and initial testing of a new experimental setup including the experimental track and PIV system. Several modifications were realized during the preparation of the experimental setup. Finally, measurements were performed with a simplified model and the results were evaluated in the form of velocity profiles in the area of interest. The most important results are the knowledge about the requirements on the model preparation. The future work will be aimed to the prototype of the ultrasonic flowmeter.
The paper describes the development of a non-invasive flowmeter for lower flow rates and its first tests. This gauge is physically based on the interaction of fluid flow with an ultrasonic signal that passes through the fluid from the transmitter to the receiver. Ultrasonic flowmeters are currently relatively commonly used gauges, whose advantages such as non-invasiveness (i.e. zero pressure losses) and the ability to seamlessly measure the flow rates of any (for example opaque) liquids, without contact with the liquid, are widely known. However, there are still parts of the ultrasonic flowmeter measurement chain that are undergoing research and development. It can be signal processing itself (mainly), its design solution, measurement for different flow cases (measurement in a flow field with a uniform velocity profile, in a flow field with an axisymmetric velocity profile, in a flow field with a general velocity profile), validation of the applied signal processing approaches, evaluation of uncertainties. The flowmeter itself, which development is described in the paper, will be used for trouble-free measurement in air engineering, but also serves as a training device for building a more complex ultrasonic gauge. Therefore, this flowmeter contains more signal transmitters and receivers than it is usual and all transmitter-receiver combinations are captured during the measurement. This gauge is called ultrasonic tomograph and its principle is also outlined in the paper. Here, so far, without a reconstructed vector field.
This paper deals with the demonstration of the non-uniformity of velocity profiles in a DN 200 air circular pipe as part of the development of a newly designed tomographic ultrasonic flowmeter. The flowmeter should measure the flow quality independently. Therefore, different aerodynamic conditions were created by placing mechanical obstacles at the entrance of the measuring chamber, and these conditions were experimentally verified. As an experimental channel substituting a section with ultrasonic sensors, a glass segment was placed at the inlet of a suction pipeline, in front of which perforated plates were inserted to break the uniformity of the velocity profile. The two-dimensional Particle Image Velocimetry (2D PIV) method was used to measure in a plane lying in the longitudinal axis of the channel. The experimental setup and PIV system parameters are described. The results are presented as velocity profiles and contour diagrams in cross-sections at different longitudinal positions in the channel. The results show that the requirement of non-uniformity is satisfied. The used disturbing plates disturb the axial symmetry of the profiles and create a backflow.
This article represents a part of an ongoing work on the preparation of an experimental rectangular channel for the PIV and LIF measurements of vortex structures and temperature field in a non-isothermal water flow. The main aim of the current study is to develop a sufficiently accurate simplified numerical model of the real problem. The basic requirements for thermal properties of heated bottom-wall are specified. In the computational model, there are several simplifications such as 2D case and a constant temperature of a heated surface along the longitudinal coordinate. Results of the numerical simulation of the fluid flow and heat transfer are verified on the experimental data obtained in a laboratory channel with the same geometry and similar flow conditions. The presented results helped to define additional requirements on the design of a new experimental channel intended for investigation of the flow instabilities in a non-isothermal liquid flow.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.