PURPOSEThe aim of this study was to compare the color stability, water sorption and cytotoxicity of thermoplastic acrylic resin for the non-metal clasp dentures to those of thermoplastic polyamide and conventional heat-polymerized denture base resins.MATERIALS AND METHODSThree types of denture base resin, which are conventional heat-polymerized acrylic resin (Paladent 20), thermoplastic polyamide resin (Bio Tone), thermoplastic acrylic resin (Acrytone) were used as materials for this study. One hundred five specimens were fabricated. For the color stability test, specimens were immersed in the coffee and green tee for 1 and 8 weeks. Color change was measured by spectrometer. Water sorption was tested after 1 and 8 weeks immersion in the water. For the test of cytotoxicity, cell viability assay was measured and cell attachment was analyzed by FE-SEM.RESULTSAll types of denture base resin showed color changes after 1 and 8 weeks immersion. However, there was no significant difference between denture base resins. All specimens showed significant color changes in the coffee than green tee. In water sorption test, thermoplastic acrylic resin showed lower values than conventional heat-polymerized acrylic resin and thermoplastic polyamide resin. Three types of denture base showed low cytotoxicity in cell viability assay. Thermoplastic acrylic resin showed the similar cell attachment but more stable attachment than conventional heat-polymerized acrylic resin.CONCLUSIONThermoplastic acrylic resin for the non-metal clasp denture showed acceptable color stability, water sorption and cytotoxicity. To verify the long stability in the mouth, additional in vitro studies are needed.
Although pulse-modulated plasma has overcome various problems encountered during the development of the high aspect ratio contact hole etching process, there is still a lack of understanding in terms of precisely how the pulse-modulated plasma solves the issues. In this research, to gain insight into previously observed phenomena, SiO2 etching characteristics were investigated under various pulsed plasma conditions and analyzed through plasma diagnostics. Specifically, the disappearance of micro-trenching from the use of pulse-modulated plasma is analyzed via self-bias, and the phenomenon that as power off-time increases, the sidewall angle increases is interpreted via radical species density and self-bias. Further, the change from etching to deposition with decreased peak power during processing is understood via self-bias and electron density. It is expected that this research will provide an informative window for the optimization of SiO2 etching and for basic processing databases including plasma diagnosis for advanced plasma processing simulators.
Arcing is a ubiquitous phenomenon and a crucial issue in high-voltage applied systems, especially low-temperature plasma (LTP) engineering. Although arcing in LTPs has attracted interest due to the severe damage it can cause, its underlying mechanism has yet to be fully understood. To elucidate the arcing mechanism, this study investigated various signals conventionally used to analyze arcing such as light emission, arcing current and voltage, and background plasma potential. As a result, we found that light emission occurs as early as 0.56 μs before arcing current initiation, which is a significant indicator of the explosive development of arcing as well as other signals. We introduce an arcing inducing probe (AIP) designed to localize arcing on the tip edge along with multiple snapshot analysis since arcing occurs randomly in space and time. Analysis reveals that the prior light emission consists of sheath and tip glows from the whole AIP sheath and the AIP tip edge, respectively. Formation mechanisms of these emissions based on multiple snapshot image analysis are discussed. This light emission before arcing current initiation provides a significant clue to understanding the arcing formation mechanism and represents a new indicator for forecasting arcing in LTPs.
Starch is one of the main carbohydrates in food; it is formed by two polysaccharides: amylose and amylopectin. The granule size of starch varies with different botanical origins and ranges from less than 1 μm to more than 100 μm. Some physicochemical and functional properties vary with the size of the granule, which makes it of great interest to find an efficient and accurate size-based separation method. In this study, the full-feed depletion mode of split-flow thin cell fractionation (FFD-SF) was employed for a size-based fractionation of two types of starch granules (corn and potato) on a large scale. The fractionation efficiency (FE) of fraction-a for corn and potato granules was 98.4 and 99.4%, respectively. The FFD-SF fractions were analyzed using optical microscopy (OM) and gravitational field-flow fractionation (GrFFF). The respective size distribution results were in close agreement for the corn starch fractions, while they were slightly different for the potato starch fractions. The thermal properties of FFD-SF fractions were analyzed, and the results for the potato starch showed that the peak temperature of gelatinization (T p) slightly decreases as the size of the granules increases. Additionally, the enthalpy of gelatinization (ΔH) increases when the granule size increases and shows negative correlation with the gelatinization range (ΔT).
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.