Thermal energy storage (TES) is extremely important in concentrated solar power (CSP) plants since it represents the main difference and advantage of CSP plants with respect to other renewable energy sources such as wind, photovoltaic, etc. CSP represents a low-carbon emission renewable source of energy, and TES allows CSP plants to have energy availability and dispatchability using available industrial technologies. Molten salts are used in CSP plants as a TES material because of their high operational temperature and stability of up to 500°C. Their main drawbacks are their relative poor thermal properties and energy storage density. A simple cost-effective way to improve thermal properties of fluids is to dope them with nanoparticles, thus obtaining the so-called salt-based nanofluids. In this work, solar salt used in CSP plants (60% NaNO3 + 40% KNO3) was doped with silica nanoparticles at different solid mass concentrations (from 0.5% to 2%). Specific heat was measured by means of differential scanning calorimetry (DSC). A maximum increase of 25.03% was found at an optimal concentration of 1 wt.% of nanoparticles. The size distribution of nanoparticle clusters present in the salt at each concentration was evaluated by means of scanning electron microscopy (SEM) and image processing, as well as by means of dynamic light scattering (DLS). The cluster size and the specific surface available depended on the solid content, and a relationship between the specific heat increment and the available particle surface area was obtained. It was proved that the mechanism involved in the specific heat increment is based on a surface phenomenon. Stability of samples was tested for several thermal cycles and thermogravimetric analysis at high temperature was carried out, the samples being stable.PACS65.: Thermal properties of condensed matter; 65.20.-w: Thermal properties of liquids; 65.20.Jk: Studies of thermodynamic properties of specific liquids

of silica-water nanofluids dispersed with an ultrasound probe: A study of their physical properties and stability. Powder Technology, 2012, Vol. 224 AbstractThe stability and agglomeration state of nanofluids are key parameters for their use in different applications. Silica nanofluids were prepared by dispersing the nanoparticles in distilled water using an ultrasonic probe, which has proved to be the most effective system and gives the best results when compared with previous works. Results were obtained concerning the influence of the solid content, pH and salt concentration on the zeta potential, electrical double layer, viscosity, elastic and viscous moduli, particle size and light backscattering. Measurement of all these properties provides information about the colloidal state of nanofluids. The most important variable is the solid content.Despite the agglomeration due to high concentration, nanofluids with low viscosity and behaving like liquid were prepared at 20% of mass load thanks to the good dispersion achieved with the ultrasonic treatment. The pH of the medium can be used to control the stability, since the nanofluids are more stable under basic conditions far from the isoelectric point (IEP) and settle at pH = 2. Therefore, stable nanofluids for at least 48 h, with high solid content, can be prepared at high pH value (pH > 7) due to the electrostatic repulsion between particles.

Nanofluids using nanoencapsulated Phase Change Materials (nePCM) allow increments in both the thermal conductivity and heat capacity of the base fluid. Incremented heat capacity is produced by the melting enthalpy of the nanoparticles core. In this work two important advances in this nanofluid type are proposed and experimentally tested. It is firstly shown that metal and metal alloy nanoparticles can be used as self-encapsulated nePCM using the metal oxide layer that forms naturally in most commercial synthesis processes as encapsulation. In line with this, Sn/SnOx nanoparticles morphology, size and thermal properties were studied by testing the suitability and performance of encapsulation at high temperatures and thermal cycling using a commercial thermal oil (Therminol 66) as the base fluid. Secondly, a mechanism to control the supercooling effect of this nePCM type based on non-eutectic alloys was developed.

The availability of Thermal Energy Storage systems in Concentrated Solar Power plants makes them suitable to handle the gap between energy supply and power demand. Increasing the total thermal energy storage capacity of the Thermal Energy Storage materials used is of interest to improve their efficiency. In this work the thermal energy storage of the so called solar salt (60% NaNO3-40% KNO3) was improved by adding a phase change material composed of Al-Cu alloy nanoencapsulated with an aluminium oxide layer naturally formed when exposed to oxygen. The resistance of the oxide shell to thermal cycling up to 570ºC and its compatibility with the molten salt were proved. The specific heat and the total thermal energy storage were evaluated at different solid mass loads. Although the specific heat and thus the sensible heat storage decreases with solid content, the contribution of the phase change enthalpy and the latent heat storage can increase the total thermal energy storage up to a 17.8% at constant volume basis comparison. Besides, the thermal conductivity of the nanofluid was increased when adding the nanoparticles improving its heat transfer performance under some particular conditions.

No abstract