Fullerene single-wall nanotubes (SWNTs) were produced in yields of more than 70 percent by condensation of a laser-vaporized carbon-nickel-cobalt mixture at 1200degreesC. X-ray diffraction and electron microscopy showed that these SWNTs are nearly uniform in diameter and that they self-organize into "ropes," which consist of 100 to 500 SWNTs in a two-dimensional triangular lattice with a lattice constant of 17 angstroms. The x-ray form factor is consistent with that of uniformly charged cylinders 13.8 +/- 0.2 angstroms in diameter. The ropes were metallic, with a single-rope resistivity of <10(-4) ohm-centimeters at 300 kelvin. The uniformity of SWNT diameter is attributed to the efficient annealing of an initial fullerene tubelet kept open by a few metal atoms; the optimum diameter is determined by competition between the strain energy of curvature of the graphene sheet and the dangling-bond energy of the open edge, where growth occurs. These factors strongly favor the metallic (10,10) tube with C5v symmetry and an open edge stabilized by triple bonds.

Single-walled carbon nanotubes (SWNTs) offer the prospect of both new fundamental science and useful (nano)technological applications 1 . High yields (70-90%) of SWNTs close-packed in bundles can be produced by laser ablation of carbon targets 2 . The electric-arc technique used to generate fullerenes and multiwalled nanotubes is cheaper and easier to implement, but previously has led to only low yields of SWNTs 3,4 . Here we show that this technique can generate large quantities of SWNTs with similar characteristics to those obtained by laser ablation. This suggests that the (still unknown) growth mechanism for SWNTs must be independent of the details of the technique used to make them. The ready availability of large amounts of SWNTs, meanwhile, should make them much more accessible for further study.In our electric arc-discharge apparatus 5 , the arc is generated between two electrodes in a reactor under a helium atmosphere (660 mbar). The cathode was a graphite rod (16 mm diameter, 40 mm long) and the anode was also a graphite rod (6 mm diameter, 100 mm long) in which a hole (3.5 mm diameter, 40 mm deep) had been drilled and filled with a mixture of a metallic catalyst and graphite powder. The arc discharge was created by a current of 100 A; a voltage drop of 30 V between the electrodes was maintained by continuously translating the anode to keep a constant distance (ϳ3 mm) between it and the cathode. Typical synthesis times were ϳ2 min. As the catalyst we used mixtures such as Ni-Co, Co-Y or Ni-Y in various atomic percentages; these are known to yield a series of interesting carbon nanostructures 6 . The mixture used by Guo et al. 7 during their laser ablation process (Co and Ni, both at 0.6 at.%) did not produce a good yield of nanotubes in our case. However, we found that a mixture of 1 at.% Y and 4.2 at.% Ni gave the best results. In this case we observed (in a total carbon mass of 2 g): (1) large quantities of rubbery soot condensed on the chamber walls; (2) web-like structures between the cathode and the reactor walls (no webs when either Y or Ni were absent); (3) a cylindrical deposit at the cathode's end; and (4) a small 'collar' (ϳ20% of the total mass) around the cathode deposit, as a black, very light and porous but free-standing material.Within all these products it was possible to observe by scanning electron microscopy (SEM; using a JEOL JSM 6300F instrument) filament-like structures that are more or less dense, depending on where in the reactor they were deposited. The 'collar' deposit was densest; the soot was the least dense. A characteristic SEM image of the collar deposit (Fig. 1) shows large amounts of entangled carbon filaments, homogeneously distributed over large areas (here at least a few square millimetres) and with diameters ranging from 10 to 20 nm. The average length between two entanglement points is several micrometres; we could not identify any filament ends. From several SEM images we estimate the yield of these filaments (with respect to the total volume of the solid material...

Single-walled carbon nanotube (SWNT)/poly(methyl methacrylate) (PMMA) nanocomposites were prepared via our coagulation method providing uniform dispersion of the nanotubes in the polymer matrix. Optical microscopy, Raman imaging, and SEM were employed to determine the dispersion of nanotube at different length scales. The linear viscoelastic behavior and electrical conductivity of these nanocomposites were investigated. At low frequencies, G‘ becomes almost independent of the frequency as nanotube loading increases, suggesting an onset of solidlike behavior in these nanocomposites. By plotting G‘ vs nanotube loading and fitting with a power law function, the rheological threshold of these nanocomposites is ∼0.12 wt %. This rheological threshold is smaller than the percolation threshold of electrical conductivity, ∼0.39 wt %. This difference in the percolation threshold is understood in terms of the smaller nanotube−nanotube distance required for electrical conductivity as compared to that required to impede polymer mobility. Furthermore, decreased SWNT alignment, improved SWNT dispersion, and/or longer polymer chains increase the elastic response of the nanocomposite, as is consistent with our description of the nanotube network.

Single-wall carbon nanotubes (SWNTs) were used to augment the thermal transport properties of industrial epoxy. Samples loaded with 1 wt% unpurified SWNT material show a 70% increase in thermal conductivity at 40K, rising to 125% at room temperature; the enhancement due to 1 wt% loading of vapor grown carbon fibers is three times smaller. Electrical conductivity data show a percolation threshold between 0.1 and 0.2 wt% SWNT loading. The Vickers hardness rises monotonically with SWNT loading up to a factor of 3.5 at 2 wt%. These results suggest that the thermal and mechanical properties of SWNT-epoxy composites are improved, without the need to chemically functionalize the nanotubes. a) present address:

Well-aligned macroscopic fibers composed solely of single-walled carbon nanotubes (SWNTs) were produced by conventional spinning. Fuming sulfuric acid charges SWNTs and promotes their ordering into an aligned phase of individual mobile SWNTs surrounded by acid anions. This ordered dispersion was extruded via solution spinning into continuous lengths of macroscopic neat SWNT fibers. Such fibers possess interesting structural composition and physical properties.