BACKGROUND: The kinetics of the thermal decomposition of cellulosic materials is of interest from the viewpoint of flame retardancy for safety, optimization of incineration processes and reducing energy production from fossil sources and associated pollution. One essential step in these processes is the thermal degradation through mass and energy transport, which determines the rate of evolution of various types of products from cellulosic materials. RESULTS: Kinetic parameters have been determined using various model‐based and model‐free methods in the thermal degradation of cellulose up to 700 °C in helium atmosphere. The values of the activation energy obtained in isothermal processes and non‐isothermal processes have been found to be not far from each other. From the integral method, the random nucleation (F1)‐type mechanism has been found most probable for cellulose degradation having an activation energy, Ea, in the range 156.5–166.5 kJ mol−1, lnA = 20–23 min−1, for first‐order reaction during its decomposition process at heating rates of 2, 5 and 10 °C min−1. Based on the high correlation coefficient, many types of mechanisms seem equally good for non‐isothermal degradation of cellulose. CONCLUSION: The linear correlation coefficient has a limitation for verifying the correctness of a reaction mechanism in the study of degradation kinetics. Therefore, the correctness of a mechanism should be considered on the basis of comparing the kinetic parameters obtained from isothermal as well as non‐isothermal methods. Copyright © 2008 Society of Chemical Industry

Cellulose arylphosphonate compounds have been synthesized and investigated by the kinetics of thermal degradation by thermogravimetry (TG) and differential scanning calorimetry (DSC) from ambient temperature to 600°C. Various kinetic and thermodynamic parameters such as energy, entropy and free energy of activation have been obtained from TG curves using the Broido method and transition state theory. The high values of enthalpy change (1016 and 1025 J g−1) of decomposition and oxidation reactions corresponding to the last two exotherms of the DSC curves of cellulose are decreased to a greater extent in the case of cellulose arylphosphonate compounds. The values of activation energy for the decomposition stage of cellulose arylphosphonate compounds lie in the range 25–49 kJ mol−1 and are found to be lower than that of pure cellulose, namely 165 kJ mol−1 in air atmosphere. Scanning electron micrographs of phosphorylated cotton cellulose and chars show furrowed and fractured surfaces although the morphology of the original fibres remains largely unchanged. Furthermore, higher char yields of cellulose derivatives leads to the conclusion that such derivitisation may give rise to flame‐retardant treatments for cellulosic materials. Copyright © 2004 Society of Chemical Industry

No abstract

This paper extends the work of Lewin et al., which showed that high levels of flame retardancy could be conferred on polyamide 6 (PA6) in the presence of small concentrations of ammonium sulphamate (AS) and dipentaerythritol (DP). PA6 samples were compounded with similarly low concentrations (2.5%w/w AS and 1%w/w DP) with or without nanoclays and fumed silica present at 1 and 2%w/w levels. Compounded samples were characterized by X‐ray diffraction, thermal analysis (differential thermal analysis/thermogravimetric analysis) and Fourier transform infrared. Flammability properties were measured by UL‐94, limiting oxygen index (LOI) and cone calorimetry test methods. All PA6 blended samples with or without nanoparticles were found to be V‐2 rated which differed from the results reported by Lewin et al. for similar samples where V‐0 ratings were obtained for clay‐free samples. LOI increases promoted by the inclusion of AS and DP alone were slightly reduced following the addition of all nanoparticles with the functionalized clays showing the largest effect. Introduction of silica, however, had the smallest effect in reducing LOI. Cone calorimetric results showed that while the presence of AS and DP raise peak heat release rate values with respect to PA6, addition of nanoparticles reduced values to below that for pure PA6. These reductions are dependent on nanoparticle concentration although differences between them, within experimental error, are very similar. While smoke generation is little affected by addition of AS and DP, the presence of nanoparticles promotes a slight increase. Results were interpreted in terms of previously published mechanisms for PA6‐AS‐DP thermal degradation and nanoparticle‐polymer interactions. Copyright © 2012 John Wiley & Sons, Ltd.

No abstract