We developed a nanocomposite with highly aligned graphite platelets in a copper matrix. Spark plasma sintering ensured an excellent copper-graphite interface for transmitting heat and stress. The resulting composite has superior thermal conductivity (500 W m(-1) K(-1), 140% of copper), which is in excellent agreement with modeling based on the effective medium approximation. The thermal expansion perpendicular to the graphite platelets drops dramatically from ∼20 ppm K(-1) for graphite and copper separately to 2 ppm K(-1) for the combined structure. We show that this originates from the layered, highly anisotropic structure of graphite combined with residual stress under ambient conditions, that is, strain-engineering of the thermal expansion. Combining excellent thermal conductivity with ultralow thermal expansion results in ideal materials for heat sinks and other devices for thermal management.

A controlled alignment of graphite nanoplatelets in a composite matrix will allow developing materials with tailored thermal properties. Achieving a high degree of alignment in a reproducible way, however, remains challenging. Here we demonstrate the alignment of graphite nanoplatelets in copper composites produced via high-energy ball milling and spark plasma sintering. The orientation of the nanoplatelets in the copper matrix is verified by polarized Raman scattering and electron microscopy showing an increasing order with increasing platelet size. The thermal conductivity k along the alignment direction is up to five times higher than perpendicular to it. The composite with the highest degree of alignment has a thermal diffusivity (100 mm(2) s(-1)) comparable to copper (105 mm(2) s(-1)) but is 20% lighter. By modeling the thermal properties of the composites within the effective medium approximation we show that (i) the Kapitza resistance is not a limiting factor for improving the thermal conductivity of a copper-graphite system and (ii) copper-graphite-nanoplatelet composites may be expected to achieve a higher thermal conductivity than copper upon further refinement.

Introduction of foreign genes into bacterial cells (transformation) is used for supplementing defective genes or providing additional biological functions. Transformation can be achieved using either chemical or physical methods, e.g., electroporation. Bulk electroporation offers several advantages over chemical methods, including high transformation efficiency, but its application is limited due to the high numbers of cells and plasmids needed as a result of the high death rate of cells during this process, and the difficulty in electroporating single cells. Synthetic inorganic gene nanocarriers have received limited attention in the transformation of bacterial cells. Here we present a plasmid delivery system based on water dispersible multi-walled carbon nanotubes (CNTs) that can simultaneously target the bacterial surface and deliver the plasmids into the cells via temporary nanochannels across the cell envelope. Transformation experiments performed on E. coli provide evidence for the high potential of CNTs for nanoscale cell electroporation.

In this study, we describe the spatial organization of CAL-72 osteoblast-like cells on arrays of vertically aligned multi-walled carbon nanotubes (VACNTs). It was observed that, unlike cell growth on non-patterned surfaces, the cell attachment and spreading process on VACNTs was significantly enhanced. Additionally, since carbon nanotubes are known to possess resilient mechanical properties and are chemically stable, the effect of periodic arrays of VACNTs on CAL-72 osteoblast-like cells was also studied. The periodicity and alignment of VACNTs considerably influenced growth, shape and orientation of the cells by steering toward the nanopattern. This situation is of great interest for the potential application of VACNTs in bone bioenginnering. This data provides evidence that CAL-72 osteoblast-like cells can sense physical features at the nanoscale. These results give a fascinating insight into the ways in which cell growth can be influenced by man-made nanostructures and could provide a framework for achieving controlled cell guidance with controlled organization and special physical properties.

A method based on the conventional lithographic technique combined with the layer-by-layer (LBL) assembly process is applied to the construction of free-standing micro- and nanostructured matrixes. The method enables controlled shaping and considerable chemical and mechanical stability of the self-assembled monolayers, allowing for high reproducibility in manufacturing. The matrixes are characterized by controlled geometry, surface topography, and chemical composition. The complete architecture is made up of successive layers of intercrossed carbon nanotubes that self-assemble into orderly structures. In particular, the present method aims to create architectures and topographies that mimic those occurring naturally (native tissue structures). In addition, nanoindentation and nanoscratch techniques were used to evaluate the mechanical properties of the carbon nanotube-based matrixes.