Additive manufacturing is becoming increasingly important as a flexible technique for a wide range of products, with applications in the transportation, health, and food sectors. However, to develop additional functionality it is important to simultaneously control structuring across multiple length scales. In 3D printing, this can be achieved by employing inks with intrinsic hierarchical order. Liquid crystalline systems represent such a class of self-organizing materials; however, to date they are only used to create filaments with nematic alignment along the extrusion direction. In this study, cholesteric hydroxypropyl cellulose (HPC) is combined with in situ photo-crosslinking to produce filaments with an internal helicoidal nanoarchitecture, enabling the direct ink writing of solid, volumetric objects with structural color. The iridescent color can be tuned across the visible spectrum by exploiting either the lyotropic or thermotropic behavior of HPC during the crosslinking step, allowing objects with different colors to be printed from the same feedstock. Furthermore, by examining the microstructure after extrusion, the role of shear within the nozzle is revealed and a mechanism proposed based on rheological measurements simulating the nozzle extrusion. Finally, by using only a sustainable biopolymer and water, a pathway toward environmentally friendly 3D printing is revealed.

Hydrogel bioadhesives have emerged as one of the most promising alternatives to sutures and staples for wound sealing and repairing, owing to their unique advantages in biocompatibility, mechanical compliance, and minimally invasive manipulation. However, only a few hydrogel bioadhesives have been successfully used for gastric perforation repair, due to their undesirable swelling when in direct contact with extremely acidic gastric fluids, and are thereby accompanied by a gradually deteriorating adhesion performance. Herein, an acid-tolerant hydrogel (ATGel) bioadhesive is developed, which integrates two distinct components, an acid-tolerant hydrogel substrate and an adhesive polymer brush layer. The ATGel bioadhesive can form instant, atraumatic, fluid-tight, and sutureless sealing of gastric perforation, and enable robust biointerfaces in direct contact with gastric fluids, addressing the key limitations with sutures and commercially-available tissue adhesives. Moreover, in vivo investigation on gastric perforation of rat model validates the proposed acid-tolerant bioadhesion, and identifies the mechanisms for accelerated gastric perforation repair through alleviated inflammation, which suppresses fibrosis and enhances angiogenesis.

Recreating tissue-specific microenvironments of the extracellular matrix (ECM) is of broad interest for the fields of tissue engineering and organ-on-a-chip. Both the biochemical and biophysical signatures of the engineered ECM interplay to affect cell response. Currently, there are limited biomaterials processing methods which allow to design ECM membrane properties flexibly and rapidly. Solvents and additives used in many existing processes also induced unwanted ECM protein degradation and toxic residues. This paper presents a solution fibre spinning technique, where careful selection of the solution combination led to well-preserved ECM proteins with tuneable composition. This technique also provides a highly versatile approach to fabricate ECM fibres and membranes, leading to designable fibre Young's modulus for over two orders of magnitude.

Flexible and stretchable light emitting devices are driving innovation in myriad applications, such as wearable and functional electronics, displays and soft robotics. However, the development of flexible electroluminescent devices via conventional techniques remains laborious and cost-prohibitive. Here, we report a facile and easily-accessible route for fabricating a class of flexible electroluminescent devices and soft robotics via direct ink writing-based 3D printing. 3D printable ion conducting, electroluminescent and insulating dielectric inks were developed, enabling facile and on-demand creation of flexible and stretchable electroluminescent devices with good fidelity. Robust interfacial adhesion with the multilayer electroluminescent devices endowed the 3D printed devices with attractive electroluminescent performance. Integrated our 3D printed electroluminescent devices with a soft quadrupedal robot and sensing units, an artificial camouflage that can instantly self-adapt to the environment by displaying matching color was fabricated, laying an efficient framework for the next generation soft camouflages.

No abstract