In the present work, the electrical and thermal performances of a newly designed PV/T (photovoltaic/thermal) air collector, which was proposed and fabricated by the author, have been investigated experimentally in the natural weather conditions. The PV/T air collector has a single-pass double-flow air channel. Also, a non-uniform cross-section transverse rib was attached at the back surface of the PV (photovoltaic) module to improve the heat transfer performance between the PV module and flowing air. The experiment was carried out in an outdoor field on a clear day with various air mass flow rates ranges from 0.0198 kg/s to 0.07698 kg/s. In the results, it was found that the average thermal efficiency of the PV/T collector increased from 35.2% to 56.72% as the air mass flow rate increased. The average electrical efficiency also increased from 14.23% to 14.81% with an increase in an air mass flow rate, but the effect of air mass flow rate on the increase in electrical efficiency was inconsiderable. The average overall efficiency, which represents the sum of electrical and thermal efficiencies, was in the range of 49.44% to 71.54% and it increased as the air mass flow rate increased. The maximum value of average overall efficiency during the test period was found to be 71.54% at an air mass flow rate of 0.07698 kg/s. From the results, it was confirmed that the newly designed PV/T air collector provides a significant enhancement in solar energy utilization.
In this study, a two-dimensional CFD (computational fluid dynamics) analysis was performed to investigate the heat-transfer and fluid-friction characteristics in a solar air heater having a transverse triangular block at the bottom of the air duct. The Reynolds number, block height (e), pitch (P), and length (l) were chosen as design parameters. The results are validated by comparing the Nusselt number predicted by simulation with available experimental results. Renormalization-group (RNG) k-ε model with enhanced wall-treatment was selected as the most appropriate turbulence model. From the results, it was found that the presence of a transverse triangular block produces a higher Nusselt number than that of smooth air duct. The enhancement in Nusselt number varied from 1.19 to 3.37, according to the geometric conditions investigated. However, the use of transverse triangular block also results in significantly higher friction losses. The thermohydraulic performance (THPP) was also estimated and has a maximum value of 1.001 for height (e) of 20 mm, length (l) of 120 mm, and pitch (P) of 150 mm, at Reynolds number of 8000. Furthermore, in the present study, correlations of the Nusselt number and friction factor were developed as a function of geometrical conditions of the transverse triangular block and Reynolds number, which can be used to predict the value of Nusselt number and friction factor with the absolute percentage deviations of 3.29% and 7.92%, respectively. solar air heater having non-uniform cross-section transverse rib roughness on the absorber plate. Akpinal and Koçyiǧit [7] analyzed the performance of a solar air heater supplied with various obstacles experimentally. Singh et al. [8] evaluated the effect of multiple arc-shaped ribs on the heat-transfer and friction characteristics, with various geometrical parameters. Singh et al. [9] investigated the heat and fluid-flow characteristics in a rectangular duct roughened with periodic discrete V-down rip. Kumar and Kim conducted a CFD-based analysis to investigate heat transfer and friction characteristics in rectangular channel with discrete multi-V-pattern ribs [10].The other method to improve the performance of a solar air heater is modifying the absorber plate. Karim and Hawlader [11] examined the performance of three types of solar air collectors having a flat-plate, v-corrugated, and finned absorber. Ho et al. [12] conducted an experimental and theoretical analysis of the double-pass cross-corrugated and double-pass V-corrugated solar air collector. Zheng et al. [13] performed experimental investigation of solar air heaters having perforating corrugated plate, slit-perforated plate, and corrugated packing. In addition to this, a number of studies have been conducted, and they mainly focused on the performance improvement by artificially roughened rip mounted on the absorber plater or modified absorber structure [14][15][16][17].Another technique to increase the heat-transfer performance of solar air heater is modifying the air duct or the shape ...
This study experimentally investigated the performance of a PVT air collector coupled with a triangular block. The triangular block, newly suggested by the authors, is a triangular-shaped obstacle and was inserted at the bottom of the PVT air collector to enhance the heat transfer performance of the collector. The experiment was carried out in actual climate conditions in Korea with two air mass flow rate conditions: 0.03606 kg/m2 s and 0.06948 kg/m2 s. Results show the average values of electrical efficiency of the collector during the test period to be 16.15% and 16.43% for each air mass flow rate, while thermal efficiencies were 28.83% and 38.36%, respectively. The average values of total energy efficiencies were found to be 44.99% and 54.79%, respectively. The results show that air mass flow rate has a large impact on thermal and total energy efficiency, while it has a small impact on electrical efficiency. Furthermore, it was confirmed that the PVT air collector coupled with a triangular block can enhance the utilization of solar energy since the thermal performance was higher than that of the collector without a triangular block.
This study discussed the effect of ribbed fin, which was suggested by the authors, on the enhancement of heat transfer and flow characteristics of fluid in a solar air heater. The ribbed fin has a rectangular rib at the base and side surfaces of the fin. Thus, it can increase the heat transfer coefficient in the fluid field of a solar air heater as well as extend the heat transfer area. The simulation was performed with various Reynolds numbers, relative heights, and pitches of the rib. The presence of the rib enhances the heat transfer performance by 3.497 times over a smooth fin. However, the addition of the rib also increases pressure drop. Thus, the thermo-hydraulic performance, which considers both heat transfer enhancement and pressure drop increase, was also discussed. Furthermore, this study developed correlations for the Nusselt number and friction factor as a function of geometric condition of the rib and Reynolds number. The correlations accurately predicted the Nusselt number for the base and side surfaces of the fin and friction factor with mean absolute percent errors of 4.24%, 4.53%, and 7.33%, respectively.
A photovoltaic thermal (PVT) collector is a type of solar collector that can simultaneously produce electrical and thermal energy from solar energy. In this research, the daily and annual performances of an air-cooled PVT collector with triangle-shaped obstacles were investigated and compared with those of a conventional air-cooled PVT collector. Based on the thermal circuit model, a numerical model of the air-cooled PVT collector containing triangle-shaped obstacles has been developed and validated using experimental results. A typical meteorological year’s weather data from Ulsan, Korea was used as the weather data. From the results, it was seen that the daily average thermal, electrical, and overall energy and exergy efficiencies for the PVT collector with triangle-shaped obstacles were 24.73%, 15.59%, 62.83%, and 15.57%, respectively, while those values of conventional PVT collector were 17.08%, 15.30%, 54.47%, and 15.13%, respectively. The results also showed that the annual energy and exergy outputs of the PVT collector with triangle-shaped obstacles were 12.84% and 1.98% greater than those of the conventional air-cooled PVT collector. From these results, it was clearly confirmed that the triangle-shaped obstacles can enhance the energy and exergy outputs of the air-cooled PVT collector.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.