No abstract

BackgroundPatient-specific modelling in clinical studies requires a realistic simulation to be performed within a reasonable computational time. The aim of this study was to develop simple but realistic outflow boundary conditions for patient-specific blood flow simulation which can be used to clarify the distribution of the anticancer agent in intra-arterial chemotherapy for oral cancer.MethodsIn this study, the boundary conditions are expressed as a zero dimension (0D) resistance model of the peripheral vessel network based on the fractal characteristics of branching arteries combined with knowledge of the circulatory system and the energy minimization principle. This resistance model was applied to four patient-specific blood flow simulations at the region where the common carotid artery bifurcates into the internal and external carotid arteries.ResultsResults of these simulations with the proposed boundary conditions were compared with the results of ultrasound measurements for the same patients. The pressure was found to be within the physiological range. The difference in velocity in the superficial temporal artery results in an error of 5.21 ± 0.78 % between the numerical results and the measurement data.ConclusionsThe proposed outflow boundary conditions, therefore, constitute a simple resistance-based model and can be used for performing accurate simulations with commercial fluid dynamics software.

Acrylic bone cement is widely used in orthopedic surgery for treating various conditions of the bone and joints. Bone cement consists of methyl methacrylate (MMA), polymethyl methacrylate (PMMA), and benzoyl peroxide (BPO), functioning as a liquid monomer, solid phase, and polymerization initiator, respectively. However, cell and tissue toxicity caused by bone cement has been a concern. This study aimed to determine the effect of tri-n-butyl borane (TBB) as an initiator on the biocompatibility of bone cement. Rat spine bone marrow-derived osteoblasts were cultured on two commercially available PMMA-BPO bone cements and a PMMA-TBB experimental material. After a 24-h incubation, more cells survived on PMMA-TBB than on PMMA-BPO. Cytomorphometry showed that the area of cell spread was greater on PMMA-TBB than on PMMA-BPO. Analysis of alkaline phosphatase activity, gene expression, and matrix mineralization showed that the osteoblastic differentiation was substantially advanced on the PMMA-TBB. Electron spin resonance (ESR) spectroscopy revealed that polymerization radical production within the PMMA-TBB was 1/15–1/20 of that within the PMMA-BPO. Thus, the use of TBB as an initiator, improved the biocompatibility and physicochemical properties of the PMMA-based material.

Biomimetic design provides novel opportunities for enhancing and functionalizing biomaterials. Here we created a zirconia surface with cactus-inspired meso-scale spikes and bone-inspired nano-scale trabecular architecture and examined its biological activity in bone generation and integration. Crisscrossing laser etching successfully engraved 60 μm wide, cactus-inspired spikes on yttria-stabilized tetragonal zirconia polycrystal (Y-TZP) with 200–300 nm trabecular bone-inspired interwoven structures on the entire surface. The height of the spikes was varied from 20 to 80 μm for optimization. Average roughness (Sa) increased from 0.10 μm (polished smooth surface) to 18.14 μm (80 μm-high spikes), while the surface area increased by up to 4.43 times. The measured dimensions of the spikes almost perfectly correlated with their estimated dimensions (R2 = 0.998). The dimensional error of forming the architecture was 1% as a coefficient of variation. Bone marrow-derived osteoblasts were cultured on a polished surface and on meso- and nano-scale hybrid textured surfaces with different spike heights. The osteoblastic differentiation was significantly promoted on the hybrid-textured surfaces compared with the polished surface, and among them the hybrid-textured surface with 40 μm-high spikes showed unparalleled performance. In vivo bone-implant integration also peaked when the hybrid-textured surface had 40 μm-high spikes. The relationships between the spike height and measures of osteoblast differentiation and the strength of bone and implant integration were non-linear. The controllable creation of meso- and nano-scale hybrid biomimetic surfaces established in this study may provide a novel technological platform and design strategy for future development of biomaterial surfaces to improve bone integration and regeneration.