Nanofibers of polymers were electrospun by creating an electrically charged jet of polymer solution at a pendent droplet. After the jet flowed away from the droplet in a nearly straight line, it bent into a complex path and other changes in shape occurred, during which electrical forces stretched and thinned it by very large ratios. After the solvent evaporated, birefringent nanofibers were left. In this article the reasons for the instability are analyzed and explained using a mathematical model. The rheological complexity of the polymer solution is included, which allows consideration of viscoelastic jets. It is shown that the longitudinal stress caused by the external electric field acting on the charge carried by the jet stabilized the straight jet for some distance. Then a lateral perturbation grew in response to the repulsive forces between adjacent elements of charge carried by the jet. The motion of segments of the jet grew rapidly into an electrically driven bending instability. The three-dimensional paths of continuous jets were calculated, both in the nearly straight region where the instability grew slowly and in the region where the bending dominated the path of the jet. The mathematical model provides a reasonable representation of the experimental data, particularly of the jet paths determined from high speed videographic observations.

No abstract

Nanofibrous scaffolds that are morphologically/structurally similar to natural ECM are highly interested for tissue engineering; however, the electrospinning technique has the difficulty in directly producing clinically relevant 3D nanofibrous scaffolds with desired structural properties. To address this challenge, we have developed an innovative technique of thermally induced nanofiber self-agglomeration (TISA) recently. The aim of this work was to prepare (via the TISA technique) and evaluate 3D electrospun PCL/PLA blend (mass ratio: 4/1) nanofibrous scaffolds having high porosity of ~95.8% as well as interconnected and hierarchically structured pores with sizes from sub-micrometers to ~300 µm for bone tissue engineering. The hypothesis was that the incorporation of PLA (with higher mechanical stiffness/modulus and bioactivity) into PCL nanofibers would significantly improve human mesenchymal stem cells (hMSCs) osteogenic differentiation in vitro and bone formation in vivo. Compared to neat PCL-3D scaffolds, PCL/PLA-3D blend scaffolds had higher mechanical properties and in vitro bioactivity; as a result, they not only enhanced the cell viability of hMSCs but also promoted the osteogenic differentiation. Furthermore, our in vivo studies revealed that PCL/PLA-3D scaffolds considerably facilitated new bone formation in a critical-sized cranial bone defect mouse model. In summary, both in vitro and in vivo results indicated that novel 3D electrospun PCL/PLA blend nanofibrous scaffolds would be strongly favorable/desired for hMSCs osteogenic differentiation and cranial bone formation.

Electrospun carbon nanofibers (ECNs) have been explored as an electrocatalyst and low-cost alternative to platinum (Pt) for triiodide reduction in dye-sensitized solar cells (DSCs). The results of electrochemical impedance spectroscopy (EIS) and cyclic voltammetry measurements indicated that the ECN counter electrodes exhibited low charge-transfer resistance (Rct), large capacitance (C), and fast reaction rates for triiodide reduction. Although the efficiency (η) of ECN-based cells was slightly lower than that of Pt-based cells, their short circuit current density (Jsc) and open circuit voltage (Voc) were comparable. The ECN-based cells achieved an energy conversion efficiency (η) of 5.5 % under the AM 1.5 illumination at 100 mW cm(-2). The reason for lower cell performance using the ECN electrode was because of its lower fill factor (FF) than that of Pt-based cells, probably caused by high total series resistance (RStot) at ∼15.5 Ω cm2, which was larger than that of ∼4.8 Ω cm2 in the Pt-based devices. Simulated results showed that the fill factor (FF) and η could be substantially improved by decreasing RStot, which might be achieved by using thinner and highly porous ECNs to reduce the thickness of the ECNs counter electrode.

No abstract