The vertical composition distribution and crystallinity of photoactive layers are considered to have critical roles in photovoltaic performance. In this concise contribution, the layer-by-layer (LBL) solution process is used to fabricate efficient polymer solar cells. The results show that the vertical composition distribution can be finely regulated via employing solvent additive 1,8-diiodooctane (DIO). The favorable vertical component distribution in tandem with improved crystallinity induced by DIO contributes to the efficient exciton dissociation, charge transportation and extraction, and limited charge recombination loss. Therefore, the optimized LBL devices yield an efficiency of 16.5%, which is higher than that of the control bulk heterojunction solar cells with an efficiency of 15.8%. Importantly, the ternary solar cells based on PM6/ Y6:PC 71 BM LBL active layers demonstrate a promising efficiency of >17%, which is the record efficiency for LBL solar devices reported to date. These findings make clear that the solvent additive-assisted LBL solution process has broader implications for the further optimization of solar cells.

Donor-acceptor (D-A) type semiconducting polymers have shown great potential for the application of deformable and stretchable electronics in recent decades. However, due to their heterogeneous structure with rigid backbones and long solubilizing side chains, the fundamental understanding of their molecular picture upon mechanical deformation still lacks investigation. Here, the molecular orientation of diketopyrrolopyrrole (DPP)-based D-A polymer thin films is probed under tensile deformation via both experimental measurements and molecular modeling. The detailed morphological analysis demonstrates highly aligned polymer crystallites upon deformation, while the degree of backbone alignment is limited within the crystalline domain. Besides, the aromatic ring on polymer backbones rotates parallel to the strain direction despite the relatively low overall chain anisotropy. The effect of side-chain length on the DPP chain alignment is observed to be less noticeable. These observations are distinct from traditional linear-chain semicrystalline polymers like polyethylene due to distinct characteristics of backbone/side-chain combination and the crystallographic characteristics in DPP polymers. Furthermore, a stable and isotropic charge carrier mobility is obtained from fabricated organic field-effect transistors. This study deconvolutes the alignment of different components within the thin-film microstructure and highlights that crystallite rotation and chain slippage are the primary deformation mechanisms for semiconducting polymers.

No abstract

Transient electronics are a rapidly emerging field due to their potential applications in the environment and human health. Recently, a few studies have incorporated acid-labile imine bonds into polymer semiconductors to impart transience; however, understanding of the structure−degradation property relationships of these polymers is limited. In this study, we systematically design and characterize a series of fully degradable diketopyrrolopyrrole-based polymers with engineered sidechains to investigate the impact of several molecular design parameters on the degradation lifetimes of these polymers. By monitoring degradation kinetics via ultraviolet−visible spectroscopy, we reveal that polymer degradation in solution is aggregationdependent based on the branching point and M n , with accelerated degradation rates facilitated by decreasing aggregation. Additionally, increasing the hydrophilicity of the polymers promotes water diffusion and therefore acid hydrolysis of the imine bonds along the polymer backbone. The aggregation properties and degradation lifetimes of these polymers rely heavily on solvent, with polymers in chlorobenzene taking six times as long to degrade as in chloroform. We develop a new method for quantifying the degradation of polymers in the thin film and observe that similar factors and considerations (e.g., interchain order, crystallite size, and hydrophilicity) used for designing high-performance semiconductors impact the degradation of imine-based polymer semiconductors. We found that terpolymerization serves as an attractive approach for achieving degradable semiconductors with both good charge transport and tuned degradation properties. This study provides crucial principles for the molecular design of degradable semiconducting polymers, and we anticipate that these findings will expedite progress toward transient electronics with controlled lifetimes.

Poly(3,4‐ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) is a popular hole transport material in perovskite solar cells (PSCs). However, the devices with PEDOT:PSS exhibit large open‐circuit voltage (Voc) loss and low efficiency, which is attributed to mismatched energy level alignment and the poor interface of PEDOT:PSS and perovskite. Here, three polymer analogues to polyaniline (PANI), PANI–carbazole (P1), PANI–phenoxazine (P2), and PANI–phenothiazine (P3) are designed with different energy levels to modify the interface between PEDOT:PSS and the perovskite layer and improve the device performance. The effects of the polymers on the device performance are demonstrated by evaluating the work function adjustment, perovskite growth control, and interface modification in MAPbI3‐based PSCs. Low bandgap Sn–Pb‐based PSCs are also fabricated to confirm the effects of the polymers. Three effects are evaluated through the comparison study of PEDOT:PSS‐based organic solar cells and MAPbI3 PSCs based on the PEDOT:PSS modified by P1, P2, and P3. The order of contribution for the three effects is work function adjustment > surface modification > perovskite growth control. MAPbI3 PSCs modified with P2 exhibit a high Voc of 1.13 V and a high‐power conversion efficiency of 21.06%. This work provides the fundamental understanding of the interface passivation effects for PEDOT:PSS‐based optoelectronic devices.