The "volcano"-relationship for the electrocatalytic hydrogen evolution reaction seems to be a generally accepted phenomenology in electrochemistry. Based on the Sabatier principle, which suggests a not too strong, nor too weak binding of reaction intermediates as prerequisite for high reaction rates, it provides a straightforward and intuitive explanation for a plethora of experimental results. However, while the Sabatier principle as a main paradigm of heterogeneous catalysis was never really disputed in the case of gas-phase reactions, it remains questionable if it can be the main driving principle that governs activity trends of electrocatalytic reactions. This work provides an overview on this topic for the model hydrogen evolution reaction (HER), pointing out certain inconsistencies and contradictions found in literature. The critical assessment provides a viewpoint which could have important practical consequences and could provide different perspective on future catalyst design

For a successful replacement of Pt, tremendous efforts have hitherto been made to develop high-performing Fe-N-C catalysts for the oxygen reduction reaction (ORR) in polymer electrolyte membrane fuel cells (PEMFCs). In comparison to the remarkable progress in activity, the stability of Fe-N-C catalysts still remains critical, however. Fe demetallation in acidic medium is hypothesized to be one critical factor for the overall lifetime. In contrast to the general belief, we herein demonstrate using an operando spectroscopic analysis that catalytically inactive Fe particles exposed to acid electrolytes cannot be fully removed by acid washing due to a relatively high open circuit potential (ca. 0.9 VRHE) leading to the formation of insoluble ferric species, whereas these particles dissolve under PEMFC operating conditions (E cathode < 0.7 VRHE) due to operando reduction to soluble ferrous cations. To overcome this issue, we demonstrate two approaches: (i) synthesis of Fe-N-C catalysts free of Fe particles and (ii) postsynthesis removal of exposed Fe particles through the control of potential using an external potentiostat or an internal reducing agent (i.e., SnCl2). Operando spectroscopic analyses verified that Fe demetallation during a given voltammetric protocol was dramatically decreased for both synthetically and postsynthetically modified Fe-N-C catalysts, while the initial ORR activity did not significantly change. However, all of these catalysts showed similar performance decay over short-term PEMFC durability tests, demonstrating the lack of a role played by ferrous cations leached from inactive Fe particles on catalyst deactivation. This supports the view that the activity is mainly imparted by FeN x C y moieties. Nevertheless, the presented guidelines are generally applicable to the whole class of Fe-N-C catalysts in order to minimize Fe demetallation in PEMFCs, which provides important advances for the future design of stable electrocatalytic systems for long-term operation.

Corrosion resistance of a transition-metal-rich PtCu3/C oxygen reduction reaction (ORR) catalyst as a representative of Pt alloy-based materials has been significantly improved by doping with small amounts of gold (<1 at. %). Transmission electron microscopy imaging shows near-surface segregation of both platinum and gold with the underlying core consisting predominantly of intermetallic PtCu3. The resulting PtAu skin catalyst shows improved resistance against Cu dissolution, as well as against carbon corrosion if compared to its PtCu3 precursor. Also, it exhibits a much higher Pt and carbon stability than a widely used Pt/C standard. Most importantly, the Au doped sample shows a substantial improvement in stability at the elevated temperature (60 degrees C) degradation test (10 000 cycles; 0.4-1.2 Vim) simulating a real PEM fuel cell environment

High oxygen evolution reaction activity of ruthenium and long term stability of iridium in acidic electrolytes make their mixed oxides attractive candidates for utilization as anodes in water electrolyzers. Indeed, such materials were addressed in numerous previous studies. The application of a scanning flow cell connected to an inductively coupled plasma mass spectrometer allowed us now to examine the stability and activity toward oxygen evolution reaction of such mixed oxides in parallel. The whole composition range of Ir-Ru mixtures has been covered in a thin film material library. In the whole composition range the rate of Ru dissolution is observed to be much higher than that of Ir. Eventually, due to the loss of Ru, the activity of the mixed oxides approaches the value corresponding to pure IrO 2 . Interestingly, the loss of only a few percent of a monolayer in Ru surface concentration results in a significant drop in activity. Several explanations of this phenomenon are discussed. It is concluded that the herein observed stability of mixed Ir-Ru oxide systems is most likely a result of high corrosion resistance of the iridium component, but not due to an alteration of the material's electronic structure. Renewable primary energies such as solar energy, wind energy and ocean energy receive more and more attention and are increasingly installed around the world.1-3 It is anticipated that renewables will eventually replace traditional fossil fuel-burning and nuclear power plants. However, intermittent power supply of renewables means that energy needs to be buffered. Thereby, hydrogen produced by water electrolysis is considered as an ideal energy carrier to adjust the balance between the generation of power by renewable primary energy and energy demand for end-use.3-5 Currently, acidic proton exchange membrane water electrolysis (PEMWE) is considered as a promising technology for this purpose. However, the widespread use of PEMWE is hindered by high capital costs, low efficiency, and shortages related to performance deterioration with time. 6 In this connection the nature of electrocatalysts and the procedure of their production and application conditions play a critical role. Materials used as electrocatalysts must be as active as possible to improve efficiency, while at the same time they need to be stable to maintain this efficiency throughout the lifetime of the electrolyzer. This is especially critical for materials catalyzing the anodic oxygen evolution reaction (OER), because of the detrimental positive potential and highly corrosive acidic environment. Only a few catalysts are able to withstand these harsh conditions, while providing sufficient activity, conductivity and mechanical stability. In fact, only iridium oxide anodes are proven to provide the required longevity of operation. On the other hand, ruthenium shows the highest electrocatalytic activity toward this reaction. 7,8 During the last decades, the electrochemical and surface properties of anodes based on these metals and their oxides we...