Monolithic all-perovskite tandem photovoltaics promise to combine low-cost and high-efficiency solar energy harvesting with the advantages of all-thin-film technologies. To date, laboratory-scale all-perovskite tandem solar cells have only been fabricated using non-scalable fabrication techniques. In response, this work reports on laser-scribed all-perovskite tandem modules processed exclusively with scalable fabrication methods (blade coating and vacuum deposition), demonstrating power conversion efficiencies up to 19.1% (aperture area, 12.25 cm2; geometric fill factor, 94.7%) and stable power output. Compared to the performance of our spin-coated reference tandem solar cells (efficiency, 23.5%; area, 0.1 cm2), our prototypes demonstrate substantial advances in the technological readiness of all-perovskite tandem photovoltaics. By means of electroluminescence imaging and laser-beam-induced current mapping, we demonstrate the homogeneous current collection in both subcells over the entire module area, which explains low losses (<5%rel) in open-circuit voltage and fill factor for our scalable modules.

Engineering of the interface between perovskite absorber thin films and charge transport layers has fueled the development of perovskite solar cells (PSCs) over the past decade. For p‐i‐n PSCs, the development and adoption of hole transport layers utilizing self‐assembled monolayers (SAM‐HTLs) based on carbazole functional groups with phosphonic acid anchoring groups has enabled almost lossless contacts, minimizing interfacial recombination to advance power conversion efficiency in single‐junction and tandem solar cells. However, so far these materials have been deposited exclusively via solution‐based methods. Here, for the first time, vacuum‐based evaporation of the most common carbazole‐based SAM‐HTLs (2PACz, MeO‐2PACz, and Me‐4PACz) is reported. X‐ray photoelectron spectroscopy and infrared spectroscopy demonstrate no observable chemical differences in the evaporated SAMs compared to solution‐processed counterparts. Consequently, the near lossless interfacial properties are either preserved or even slightly improved as demonstrated via photoluminescence measurements and an enhancement in open‐circuit voltage. Strikingly, applying evaporated SAM‐HTLs to complete PSCs demonstrates comparable performance to their solution‐processed counterparts. Furthermore, vacuum deposition is found to improve perovskite wetting and fabrication yield on previously non‐ideal materials (namely Me‐4PACz) and to display conformal and high‐quality coating of micrometer‐sized textured surfaces, improving the versatility of these materials without sacrificing their beneficial properties.

Monolithic two-terminal (2T) perovskite/CuInSe 2 (CIS) tandem solar cells (TSCs) combine the promise of an efficient tandem photovoltaic (PV) technology with the simplicity of an all-thin-film device architecture that is compatible with flexible and lightweight PV. In this work, we present the first-ever 2T perovskite/CIS TSC with a power conversion efficiency (PCE) approaching 25% (23.5% certified, area 0.5 cm 2 ). The relatively planar surface profile and narrow band gap (∼1.03 eV) of our CIS bottom cell allow us to exploit the optoelectronic properties and photostability of a low-Br-containing perovskite top cell as revealed by advanced characterization techniques. Current matching was attained by proper tuning of the thickness and bandgap of the perovskite, along with the optimization of an antireflective coating for improved light in-coupling. Our study sets the baseline for fabricating efficient perovskite/CIS TSCs, paving the way for future developments that might push the efficiencies to over 30%.

Given the outstanding progress in research over the past decade, perovskite photovoltaics (PV) is about to step up from laboratory prototypes to commercial products.For this to happen, realizing scalable processes to allow the technology to transition from solar cells to modules is pivotal. This work presents all-evaporated perovskite PV modules with all thin films coated by established vacuum deposition processes. A common 532-nm nanosecond laser source is employed to realize all three interconnection lines of the solar modules. The resulting module interconnections exhibit low series resistance and a small total lateral extension down to 160 μm. In comparison with interconnection fabrication approaches utilizing multiple scribing tools, the process complexity is reduced while the obtained geometrical fill factor of 96% is comparable with established inorganic thin-film PV technologies. The all-evaporated perovskite minimodules demonstrate power conversion efficiencies of 18.0% and 16.6% on aperture areas of 4 and 51 cm 2 , respectively. Most importantly, the allevaporated minimodules exhibit only minimal upscaling losses as low as 3.1% rel per decade of upscaled area, at the same time being the most efficient perovskite PV minimodules based on an all-evaporated layer stack sequence.

Thermal images generated from infrared radiation are useful for monitoring many processes; however, infrared cameras are orders of magnitude more expensive than their visible counterparts. Methods that allow visible cameras to capture thermal images are therefore of interest. In this contribution, thermal images of a surface coated with an inexpensive inorganic micropowder phosphor are generated from the analysis of a video taken with a smartphone camera. The phosphor is designed to have a temperature‐dependent emission lifetime that is long enough to be determined from the analysis of a 30 frames‐per‐second video recording. This proof‐of‐principle work allows temperatures in the 270–320 K range to be accurately determined with a precision better than 2 K, even in the presence of bright background illuminance up to 1500 lm m−2. In the broader context, this inspires further development of phosphors to bring time‐resolved sensing techniques into lifetime long enough ranges to allow smartphone‐based detection.