Nichtbelüftete Flachdachkonstruktionen in Holzbauweise erfordern aufgrund ihrer Kompaktheit tiefere Kenntnisse hinsichtlich deren bauphysikalischer Vorgänge im Dach. Dabei weist vor allem die Dachschalung aus Holz unterhalb der dampfdiffusionsdichten Schicht ein feuchtetechnisch erhöhtes Gefahrenpotential auf. Untersuchungen haben gezeigt, dass eine Überschreitung von 20 % Holzfeuchte über eine längere Zeitdauer erhebliche Folgen wie Befall durch Schimmelpilze oder holzzerstörende Pilze bedeuten kann. Auch die Verklebung kann bei so hohen Holzfeuchten deutlich beeinträchtigt werden. Aus diesem Grund wurde im Rahmen eines Forschungsprojektes beim Neubau eines Zweifamilienhauses Messtechnik im Hohlkastensystem installiert und die Konstruktion über mehrere Jahre überwacht. In die Dachkonstruktion wurden vergleichend Mineralwolle‐ und eine Holzfaserdämmung eingebaut. Zur Beurteilung des Feuchtegehaltes der Dachschalung wurde dabei auf zwei experimentelle und ein numerisches Verfahren zurückgegriffen. Das erste experimentelle Verfahren basiert auf der Berechnung der Holzfeuchte aus den gemessenen relativen Luftfeuchten im Dach. Hierfür wurde speziell die Sorptionsisotherme der verwendeten Dreischichtplatten ermittelt. Parallel dazu wurde die Holzfeuchte mittels Widerstandsmessung in den Bereichen mit Holzfaser‐ bzw. Mineralwolledämmung bestimmt. Zum Vergleich dieser experimentellen Verfahren wurde numerisch eine instationäre hygrothermische Bauteilberechnung mittels WUFI® simuliert. Alle drei Verfahren ergeben plausible Ergebnisse. Aufgrund der maximalen Abweichungen von 2 % untereinander kann davon ausgegangen werden, dass sich der Verlauf der Ausgleichsfeuchte der Dreischichtplatte in einem Bereich zwischen ca. 11 bis 19 % Holzfeuchte bewegt. Somit liegt sie unter der kritischen Grenze von 20 % und stellt theoretisch keine feuchtetechnische Gefahr dar. Nichtdestotrotz muss aber die Feuchtebeständigkeit der Verklebung dabei unbedingt ebenfalls beachtet werden. Experimental and numerical investigation on the hygrothermal behaviour of flat roof elements made in hollow boxed construction. Due to their compactness non‐ventilated flat roof constructions in wood require deeper knowledge about the construction‐physical processes. The wooden roof sheathing below the vapour diffusion tight layer, in particular, runs an increased risk of hygric properties. Studies have shown that an excess of 20 % moisture content during a longer period of time implicates significant consequences, such as moulds, etc. The bonding can be significantly affected at such high moisture contents. For this reason, as part of a research project a measurement technology was installed during the new construction of a two family house and monitored over several years. For comparative analysis areas with mineral fibrous and soft fibrous insulating material were established. Two experimental and one numerical methods were applied in order to assess the moisture content of the installed three‐layer panel. The first experimental method is based on t...
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.