Mischaracterization of so lar cell power conversion efficiencies and widespread publication of inconsistent data in scientific journals th reate ns to undermine progress in orga nic and hybrid photovoltaics research.

Low‐cost hybrid solar cells have made tremendous steps forward during the past decade owing to the implementation of extremely thin inorganic coatings as absorber layers, typically in combination with organic hole transporters. Using only extremely thin films of these absorbers reduces the requirement of single crystalline high‐quality materials and paves the way for low‐cost solution processing compatible with roll‐to‐roll fabrication processes. To date, the most efficient absorber material, except for the recently introduced organic–inorganic lead halide perovskites, has been Sb2S3, which can be implemented in hybrid photovoltaics using a simple chemical bath deposition. Current high‐efficiency Sb2S3 devices utilize absorber coatings on nanostructured TiO2 electrodes in combination with polymeric hole transporters. This geometry has so far been the state of the art, even though flat junction devices would be conceptually simpler with the additional potential of higher open circuit voltages due to reduced charge carrier recombination. Besides, the role of the hole transporter is not completely clarified yet. In particular, additional photocurrent contribution from the polymers has not been directly shown, which points toward detrimental parasitic light absorption in the polymers. This study presents a fine‐tuned chemical bath deposition method that allows fabricating solution‐processed low‐cost flat junction Sb2S3 solar cells with the highest open circuit voltage reported so far for chemical bath devices and efficiencies exceeding 4%. Characterization of back‐illuminated solar cells in combination with transfer matrix‐based simulations further allows to address the issue of absorption losses in the hole transport material and outline a pathway toward more efficient future devices.

Lead halide perovskite solar cells have shown a tremendous rise in power conversion efficiency with reported record efficiencies of over 20% making this material very promising as a low cost alternative to conventional inorganic solar cells. However, due to a differently severe "hysteretic" behaviour during current density-voltage measurements, which strongly depends on scan rate, device and measurement history, preparation method, device architecture, etc., commonly used solar cell measurements do not give reliable or even reproducible results. For the aspect of commercialization and the possibility to compare results of different devices among different laboratories, it is necessary to establish a measurement protocol which gives reproducible results

Significant progress in solar-cell research is currently made by the development of metal-organic perovskites (MOPs) owing to their superior properties, such as high absorption coefficients and effective transport of photogenerated charges. As for other semiconductors, it is expected that the properties of MOPs may be significantly improved by a defined nanostructure. However, their chemical sensitivity (e.g., towards hydrolysis) prohibits the application of methods already known for the synthesis of other nanomaterials. A new and general method for the synthesis of various (CH3NH3)PbI3 nanostructures from a novel single-source precursor is presented. Nanoporous MOP single crystals are obtained by a crystal-to-crystal transformation that is accompanied by spinodal demixing of the triethylene glycol containing precursor structure. Selective binding of a capping agent can be used to tune the particle shape of the MOP nanocrystals.

Polymer morphology and aggregation play an essential role for efficient charge carrier transport and charge separation in polymer-based electronic devices. It is a common method to apply the H-aggregate model to UV/Vis or photoluminescence spectra in order to analyze polymer aggregation. In this work we present strategies to obtain reliable and conclusive information on polymer aggregation and morphology based on the application of an H-aggregate analysis on UV/Vis and photoluminescence spectra. We demonstrate, with P3HT as model system, that thickness dependent reflection behavior can lead to misinterpretation of UV/Vis spectra within the H-aggregate model. Values for the exciton bandwidth can deviate by a factor of two for polymer thicknesses below 150 nm. In contrast, photoluminescence spectra are found to be a reliable basis for characterization of polymer aggregation due to their weaker dependence on the wavelength dependent refractive index of the polymer. We demonstrate this by studying the influence of surface characteristics on polymer aggregation for spin-coated thin-films that are commonly used in organic and hybrid solar cells.

Sb 2 S 3 is a promising candidate for solar cell absorbers due to its high absorption coefficient, suitable band gap and earth-abundant constituents. Here we present the preparation of hybrid solar cells from an ink of colloidal Sb 2 S 3 nanoparticles and P3HT. Colloidal Sb 2 S 3 nanoparticles were prepared via hot injection method. Solar cells based on these nanoparticles achieves a power conversion efficiency of 1.5%, which is efficiency record for planar hybrid solar cells based on Sb 2 S 3 nanoparticles. We investigated in detail the role of the capping agents on the performance of solar cells.

Despite their outstanding photovoltaic performance, organic–inorganic perovskite solar cells still face severe stability issues and limitations in their device dimension. Further development of perovskite solar cells therefore requires a deeper understanding of loss mechanisms, in particular, concerning the origin and impact of trap states. Here, different surface properties of submicrometer sized CH3NH3PbI3 particles are studied as a model system by photoluminescence spectroscopy to investigate the impact of the perovskite crystal surface on photoexcited states. Comparison of single crystals with either isolating or electron‐rich surface passivation indicates the presence of positively charged surface trap states that can be passivated in case of the latter. These surface trap states cause enhanced nonradiative recombination at room temperature, which is a loss mechanism for solar cell performance. In the orthorhombic phase, the origin of multiple emission peaks is identified as the recombination of free and bound excitons, whose population ratio critically depends on trap state properties. The dynamics of exciton trapping at 50 K are observed on a time‐scale of tens of picoseconds by a simultaneous population decrease and increase of free and bound excitons, respectively. These results emphasize the potential of surface passivation to further improve the performance of perovskite solar cells.

Particle-based semiconductor materials are promising constituents of future technologies. They are described by unique features resulting from the combination of discrete nanoparticle characteristics and the emergence of cooperative phenomena based on long-range interaction within their superstructure. (Nano)particles of outstanding quality with regards to size and shape can be prepared via colloidal synthesis using appropriate capping agents. The classical capping agents are electrically insulating, which impedes particle-particle electronic communication. Consequently, there exists a high demand for realizing charge transport through interfaces especially for semiconductors of relevance like hybrid perovskites (HYPEs), for example, CHNHPbI (MAPI) as one of the most prominent representatives. Of particular interest are crystals in the micrometer range, as they possess synergistic advantages of single crystalline bulk properties, shape control as well as the possibility of being functionalized. Here we provide a synthetic strategy toward thiophene-functionalized single crystalline MAPI microrods originating from the single source precursor CHNHPbITEG (TEG = triethylene glycol). In the dark, the microrods show enhanced charge transport characteristics of holes over 2 orders of magnitude compared to microscale cuboids with insulating alkyl surface modifiers and nonfunctionalized random sized particles. In large-area prototype photodetector devices (2.21 cm), the thiophene functionalization improves the response times because of the interparticle charge transport (t = 190 ms, t = 430 ms) compared to alkyl-functionalized particles (t = 1055 ms, t = 60 ms), at similar responsivities of 0.65 and 0.71 mA W, respectively. Further, the surface functionalization and crystal grains on the micrometer scale improve the device stability. Therefore, this study provides clear evidence for the interplay and importance of crystal size, shape and surface modification of MAPI crystals, which is of major importance in every optoelectronic device.