A wet mixing process is proposed for filled rubber composites with a high silica loading to overcome the drawbacks of high energy consumption and workplace contamination of the conventional dry mixing process. Ball milling was adopted for preparing the silica dispersion because it has a simple structure, is easy to operate, and is a low-cost process that can be easily scaled up for industrial production. The response surface methodology was used to optimize the making of the silica dispersion. The optimum conditions for a well-dispersed silica suspension with the smallest silica particle size of 4.9 mm were an about 22% silica content and 62 h of ball milling. The effects of dry and wet mixing methods on the properties of silica-filled rubber composites were investigated in a broad range of silica levels from low to high loadings. The mixing method choice had little impact on the properties of rubber composites with low silica loadings. The silica-filled rubber demonstrated in this study, however, shows superior characteristics over the rubber composite prepared with conventional dry mixing, particularly with high silica loadings. When compared to silica-filled natural rubbers prepared by dry mixing (dry silica rubber, DSR), the wet mixing (for WSR) produced smaller silica aggregates with better dispersion. Due to the shorter heat history, the WSR exhibits superior curing characteristics such as a longer scorch time (2.2–3.3 min for WSR and 1.0–2.1 min for DSR) and curing time (4.1–4.5 min for WSR and 2.2–3.1 min for DSR). Additionally, the WSR has superior mechanical properties (hardness, modulus, tensile strength, and especially the elongation at break (420–680% for WSR and 360–620% DSR)) over the DSR. The rolling resistance of WSR is lower than that of DSR. However, the reversed trend on the wet skid resistance is observed.
Stirred tanks are prevalent in various industries, including chemical, biochemical, and pharmaceutical industries. These reactors are suitable for ensuring efficient mass and heat transfer because adequate mixing can be achieved. Numerous studies have been conducted on small-scale stirred-tank reactors. However, upscaling such reactors is challenging because of the complex flow behavior inside the system, especially for the mixing of immiscible liquid–liquid systems. Thus, the objectives of this study were to examine the flow behavior and upscale an immiscible liquid–liquid stirred tank using CFD simulation by investigating a flat-bottomed stirred tank reactor, equipped with a six-blade Rushton turbine. The simulated results were in good agreement with those obtained experimentally. The scale of the reactor significantly affects the hydrodynamic behavior, and the uniformity of the radial distribution of the velocity decreases with increasing Reynolds number. Furthermore, the upscaling criteria were evaluated for geometric similarity and equal mixing times. The proposed scaling law reliably scaled up the immiscible liquid–liquid mixing in a stirred tank with a difference in the range of ±10%.
In this research, effects of filler types and their loading on properties of the natural rubber closed cell foam were investigated. The azodicarbonamide was used as a blowing agent in 4 phr loading. The filler types that are the N-330 grade of carbon black, precipitated calcium carbonate and rubber grade china clay, their loading was varied from 0 to 50 phr (part per hundred dried rubber). The physical properties of the rubber foam that are the difference torque from the oscillating disk rheometer, hardness, tear strength, 300% modulus, tensile strength, elongation at break and compression set were analyzed. The results were found that the carbon black was yielded the highest of all properties in every loading. In conclusion, the suitable filler for closed cell rubber foam is the carbon black.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.