A solvent atmosphere results in the degradation of P3HT:PCBM solar cells due to the formation of large PCBM crystallites.

Polymer topology and reduced dimensions can have a significant impact on the properties and phase transitions of polymeric films with thicknesses below a few hundred nanometers. We study the impact of these effects in the case of thin films of cyclic and linear poly­(N-isopropylacrylamide) (PNIPAM) exposed to water vapor. Specifically, we monitor the swelling kinetics of the thin PNIPAM films, their interfacial interactions, and their LCST-type demixing phase transition, using white light interferometry and X-ray reflectivity. As the film thickness decreases, the swelling ratio increases, presumably due to the increasingly dominant effect of polymer/substrate interactions. The time constants of the swelling process depend on both the film thickness and the PNIPAM topology. Consistent with earlier observations for PNIPAM solutions, in thin swollen films of comparable concentration, cyclic PNIPAM exhibits a broader and thus less cooperative demixing transition than the linear PNIPAM counterpart.

Microgel particles of cross-linked poly(NIPAM-co-acrylic acid) with different acrylic acid contents are investigated in solution and in the adsorbed state. As a substrate, silicon with a poly(allylamine hydrochloride) (PAH) coating is used. The temperature dependence of the deswelling of the microgel particles was probed with atomic force microscopy (AFM). The inner structure of the adsorbed microgel particles was detected with grazing incidence small angle neutron scattering (GISANS). Small angle neutron scattering (SANS) on corresponding microgel suspensions was performed for comparison. Whereas the correlation length of the polymer network shows a divergence in the bulk samples, in the adsorbed microgel particles it remains unchanged over the entire temperature range. In addition, GISANS indicates changes in the particles along the surface normal. This suggests that the presence of a solid surface suppresses the divergence of internal fluctuations in the adsorbed microgels close to the volume phase transition.

Processing solvent additives in polymer:fullerene bulk heterojunction systems are known as a promising method to enhance photovoltaic performance. It is generally agreed that solvent additives enable polymers to have a high degree of molecular order which increases the device performance. However, the understanding of the efficiency enhancement is not complete. There is a lack of insight regarding the quantitative determination of the molecular miscibility between polymer and fullerene as well as the inner morphology changes induced by the additives. In this work, understanding of the influence of the solvent additive 1,8-octanedithiol (ODT) is provided on the classic system poly(3-hexylthiophene-2,5-diyl):[6,6]-phenyl-C61 butyric acid methyl ester (P3HT:PCBM) films. The impact on polymer crystallinity, surface structure, inner morphology, and quantitative molecular miscibility of P3HT and PCBM is studied as a function of ODT volume concentration. The crystallinity is probed with absorption spectroscopy and grazing incidence wide-angle X-ray scattering. The morphology and miscibility are characterized via atomic force microscopy and time-of-flight grazing incidence small angle neutron scattering. Besides an increased crystallinity and prominent phase separation, ODT increases the solubility of PCBM in P3HT and reduces the size of amorphous P3HT domains. Moreover, solvent processing with a high ODT concentration alters the vertical material composition of the active layer.

The performance of organic photovoltaic cells (OPVCs) shows a critical dependence on morphology and structure of the active layers. In small molecule donor/acceptor (D/A) cells fabrication parameters, like substrate temperature and evaporation rate, play a significant role for crystallization and roughening of the film. In particular, the fraction of mixed material at the interface between donor and acceptor is highly relevant for device performance. While an ideal planar heterojunction (PHJ) exhibits the smallest possible interface area resulting in suppressed recombination losses, mixed layers suffer strongly from recombination but show higher exciton dissociation efficiencies. In this study we investigate PHJ and planar‐mixed heterojunction (PM‐HJ) solar cells based on diindenoperylene (DIP) as donor and C60 as acceptor, fabricated under different growth conditions. Grazing incidence small angle X‐ray scattering (GISAXS), X‐ray reflectometry (XRR) and atomic force microscopy (AFM) are used to obtain detailed information about in‐ and out‐of‐plane structures and topography. In that way we find that surface and bulk domain distances are correlated in size for PHJs, while PM‐HJs show no correlation at all. The resulting solar cell characteristics are strongly affected by the morphology, as reorganizations in structure correlate with changes in the solar cell performance.