This study aims to understand the visible light photocatalytic activities of platinized WO3 (Pt/WO3) on the degradation of aquatic pollutants and the role of main photooxidants. The presence of Pt on WO3 is known to facilitate the multielectron reduction of O2, which enables O2 to serve as an electron acceptor despite the insufficient reduction potential of the conduction band electrons (in WO3) for the one-electron reduction of O2. The concurrent oxidative reactions occurring on WO3 were markedly enhanced in the presence of Pt and accompanied the production of OH radicals under visible light, which was confirmed by both a fluorescence method (using a chemical trap) and a spin trap method. The generation of OH radicals mainly comes from the reductive decomposition of H2O2 that is produced in situ from the reduction of O2 on Pt/WO3. The rate of in situ production of H2O2 under visible light was significantly faster with Pt/WO3 than WO3. Six substrates that were tested for the visible light (lambda>420 nm) induced degradation on Pt/WO3 included dichloroacetate (DCA), 4-chlorophenol (4-CP), tetramethylammonium (TMA), arsenite (As(III)), methylene blue (MB), and acid orange 7 (AO7). The degradation (or conversion) of all six substrates was successfully achieved with Pt/WO3 and the role of OH radicals in Pt/WO3 photocatalysis seemed to be different depending on the kind of substrate. In the presence of tert-butyl alcohol (TBA: OH radical scavenger), the photocatalytic degradation was markedly reduced for 4-CP or completely inhibited for DCA and TMA whereas that of As(III), MB, and AO7 was little affected. Pt/WO3 photocatalyst that oxidizes various substrates under visible light with a sufficient photostability can be applied for solar water treatment.

No abstract

In this article, we report a controllable and reproducible approach to prepare highly ordered 2-D hexagonal mesoporous crystalline TiO2-SiO2 nanocomposites with variable Ti/Si ratios (0 to infinity). XRD, TEM, and N2 sorption techniques have been used to systematically investigate the pore wall structure, and thermal stability functioned with the synthetic conditions. The resultant materials are ultra highly stable (over 900 degrees C), have large uniform pore diameters (approximately 6.8 nm), and have high Brunauer-Emmett-Teller specific surface areas (approximately 290 m2/g). These mesostructured TiO2-SiO2 composites were obtained using titanium isopropoxide (TIPO) and tetraethyl orthosilicate (TEOS) as precursors and triblock copolymer P123 as a template based on the solvent evaporation-induced co-self-assembly process under a large amount of HCl. Our strategy was the synchronous assembly of titanate and silicate oligomers with triblock copolymer P123 by finely tuning the relative humidity of the surrounding atmosphere and evaporation temperature according to the Ti/Si ratio. We added a large amount of acidity to lower condensation and polymerization rates of TIPO and accelerate the rates for TEOS molecules. TEM and XRD measurements clearly show that the titania is made of highly crystalline anatase nanoparticles, which are uniformly embedded in the pore walls to form the "bricked-mortar" frameworks. The amorphous silica acts as a glue linking the TiO2 nanocrystals and improves the thermal stability. As the silica contents increase, the thermal stability of the resulting mesoporous TiO2-SiO2 nanocomposites increases and the size of anatase nanocrystals decreases. Our results show that the unique composite frameworks make the mesostructures overwhelmingly stable; even with high Ti/Si ratios (> or =80/20) the stability of the composites is higher than 900 degrees C. The mesoporous TiO2-SiO2 nanocomposites exhibit excellent photocatalytic activities (which are higher than that for commercial catalyst P25) for the degradation of rhodamine B in aqueous suspension. The excellent photocatalytic activities are ascribed to the bifunctional effect of highly crystallized anatase nanoparticles and high porosity.