a b s t r a c tA failure investigation was conducted on a high-pressure machine with a large pump-turbine runner that was 2.9 m in diameter and had a maximum discharge rate of 32 m 3 /s.A part of the runner broke off during operation. This released a piece of the crown, which went through the machine, causing further damage. An analysis of the broken runner revealed a fatigue problem, so the dynamic/vibratory behavior of the runner during machine operation was investigated to determine the cause.First, the excitation forces acting on the runner during operation were studied. The main excitation in pump-turbines is generated by the interference between the rotating blades and the stationary vanes, known as a rotor-stator interaction (RSI), which produces large pressure pulsations. The amplitude of the pressure pulsations was measured in the prototype using pressure transducers.Second, the modal response of the runner structure was analyzed. A finite element (FEM) model of the runner was developed and the main natural frequencies and associated mode shapes were identified.A dynamic analysis was then performed to determine the runner response. A harmonic excitation simulating the pressure pulsation of the RSI was applied to the numerical model of the runner. The results showed a large stress concentration in the T-joint between the blade and crown where the crack originated. Finally, the possible causes of the damage are discussed.
Abstract:Hydropower plays a key role in the actual energy market due to its fast response and regulation capacity. In that way, hydraulic turbines are increasingly demanded to work at off-design conditions, where complex flow patterns and cavitation appear, especially in Francis turbines. The draft tube cavitation surge is a hydraulic phenomenon that appears in Francis turbines below and above its Best Efficiency Point (BEP). It is a low frequency phenomenon consisting of a vortex rope in the runner outlet and draft tube, which can become unstable when its frequency coincides with a natural frequency of the hydraulic circuit. At this situation, the output power can significantly swing, endangering the electrical grid stability. This study is focused on the detection of these instabilities in Francis turbines and their relationship with the output power swings. To do so, extensive experimental tests for different operating conditions have been carried out in a large prototype Francis turbine (444 MW of rated power) within the frame of the European Project Hyperbole (FP7-ENERGY-2013-1). Several sensors have been installed in the hydraulic circuit (pressure sensors in the draft tube, spiral casing, and penstock), in the rotating and static structures (vibration sensors, proximity probes, and strain gauges in the runner and in the shaft), as well as in the electrical side (output power, intensity, and voltage). Moreover, a numerical Finite Element Method (FEM) has been also used to relate the hydraulic excitation with the output power swing.
Pumped storage hydropower plants are of paramount importance for the stability of the electrical grid. They can store huge amounts of energy by pumping water from a lower to a higher reservoir (pump operation) converting the surplus of electrical energy into potential energy [1]. At peak hours or in case of emergency this potential energy is converted again into electrical energy and delivered to the grid.The machines used in these power plants are generally reversible pump-turbines (RPT). RPT are high performance machines that have to change operation from pump to turbine mode (reversing runner rotation and flow direction) in a short time. Due to their special design characteristics (large power concentration) and operating conditions, they generate large dynamic forces when in operation. In the last years, due to the massive entrance of wind power, the number of start/stop cycles of RPT has increased dramatically as well as the operation at off-design conditions subjecting the machine to large dynamic forces. The RPT rotating train and structure has to resist all these forces for a lifespan of several decades. In this new scenario, more cases of damage have been reported and a more advanced and effective vibration monitoring is necessary.Compared with a conventional hydro turbine these machines have less number of blades (6 to 9) and higher rotating speeds operating at high pressure. The main excitation phenomenon is the well-known rotor-stator interaction (RSI) [2][3][4][5]. This excitation occurs in other kind of turbomachinery [2], but is critical in RPT due to the low number of blades and to the high head (difference in altitude between the upper and the lower reservoir). In some studies [3, 6, 7], RSI is supposed to be the cause of the failures found.In this paper the vibration monitoring in RPT is analysed. The characteristics of the main excitation forces and the procedure used to select the monitoring parameters (spectral bands) are presented. An analysis of the vibration signatures measured in different machines as well as the main types of damage found after several year of monitoring are introduced and discussed. 2.Vibration based condition monitoring system Description of the monitoring systemSince 1992 several pump-turbine units have been monitored. A reversible pumpturbine unit is a vertical shaft machine with a hydraulic turbine in the bottom and an electrical generator in the top. Typical RPT have three radial bearings, one in the turbine and two in the electrical generator, as well as one axial thrust bearing. For monitoring, sensors were located in all the bearings and in other positions depending on the machine (Figure 1).The signals from accelerometers and pressure sensors were acquired as well as the signals related to the operating conditions of the machine (head, distributor opening, pump/turbine operation).In the beginning off-line monitoring using data collectors were used. In 1998 remote on-line monitoring systems were installed in many of them (Figure 2). Acquisition systems MVX from...
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.