Monolithic realization of metallic 1T and semiconducting 2H phases makes MoS2 a potential candidate for future microelectronic circuits. A method for engineering a stable 1T phase from the 2H phase in a scalable manner and an in-depth electrical characterization of the 1T phase is wanting at large. Here we demonstrate a controllable and scalable 2H to 1T phase engineering technique for MoS2 using microwave plasma. Our method allows lithographically defining 1T regions on a 2H sample. The 1T samples show excellent temporal and thermal stability making it suitable for standard device fabrication techniques. We conduct both two-probe and four-probe electrical transport measurements on devices with back-gated field effect transistor geometry in a temperature range of 4 K to 300 K. The 1T samples exhibit Ohmic current-voltage characteristics in all temperature ranges without any dependence to the gate voltage, a signature of a metallic state. The sheet resistance of our 1T MoS2 sample is considerably lower and the carrier concentration is a few orders of magnitude higher than that of the 2H samples. In addition, our samples show negligible temperature dependence of resistance from 4 K to 300 K ruling out any hoping mediated or activated electrical transport.

Two-dimensional (2D) superconductivity is a fascinating phenomenon packed with rich physics and wide technological application. The vortices and their dynamics arising from classical and quantum fluctuations give rise to Berezinskii-Kosterlitz-Thouless (BKT) transition and 2D Bose metallic phase both of which are of fundamental interest. In 2D, observation of superconductivity and the associated phenomena are sensitive to material disorders. Highly crystalline and inherently 2D van der Waals (vW) systems with carrier concentration and conductivity approaching metallic regime have been a potential platform. The metallic 1T phase of MoS2, a widely explored vW material system controllably, engineered from the semiconducting 2H phase, is a tangible choice. Here, we report the observation of 2D superconductivity accompanied by BKT transition and Bose metallic state in a few-layer 1T-MoS2. Structural characterization shows excellent crystallinity over extended lateral dimension. The electrical characterization confirms the metallic nature down to 4 K and a transition to a superconducting state below 1.2 K with a Tc ~ 920 mK. The 2D nature of the superconducting state is confirmed from the magneto-transport anisotropy against field orientations and the presence of BKT transition. In addition, our sample showcases a manifold increase in the parallel upper-critical-field above the Pauli limit. The inherent twodimensionality and possibility of scalably engineering semiconducting, metallic and superconducting phases makes MoS2 a potential candidate for hosting monolithic all-twodimensional hybrid quantum devices.

We have used Bi 2 Se 3 nanoribbons, grown by catalyst-free Physical Vapor Deposition to fabricate high quality Josephson junctions with Al superconducting electrodes. In our devices we observe a pronounced reduction of the Josephson critical current density J c by reducing the width of the junction, which in our case corresponds to the width of the nanoribbon. Because the topological surface states extend over the entire circumference of the nanoribbon, the superconducting transport associated to them is carried by modes on both the top and bottom surfaces of the nanoribbon. We show that the J c reduction as a function of the nanoribbons width can be accounted for by assuming that only the modes travelling on the top surface contribute to the Josephson transport as we derive by geometrical consideration. This finding is of a great relevance for topological quantum circuitry schemes, since it indicates that the Josephson current is mainly carried by the topological surface states.

We used the asymmetric superconducting quantum interference device (SQUID) technique to extract the current phase relation (CPR) of a Josephson junction with a 3D-topological insulator (TI) Bi2Se3 nanobelt as the barrier. The obtained CPR shows deviations from the standard sinusoidal CPR with a pronounced forward skewness. At temperatures below 200 mK, the junction skewness values are above the zero temperature limit for short diffusive junctions. Fitting of the extracted CPR shows that most of the supercurrent is carried by ballistic topological surface states (TSSs), with a small contribution of diffusive channels primarily due to the bulk. These findings are instrumental in engineering devices that can fully exploit the properties of the topologically protected surface states of 3D TIs.