It is shown that when modeling the processes of forging and stamping, it is necessary to take into account not only the hardening of the material, but also softening, which occurs during hot processing. Otherwise, the power parameters of the deformation processes are precisely determined, which leads to the choice of more powerful equipment. Softening accounting (processes of stress relaxation) will allow to accurately determine the stress and strain state (SSS) of the workpiece, as well as the power parameters of the processes of deformation. This will expand the technological capabilities of these processes. Existing commercial software systems for modeling hot plastic deformations based on the finite element method (FEM) do not allow this. This is due to the absence in these software products of the communication model of the component deformation rates and stresses, which would take into account stress relaxation. As a result, on the basis of the Maxwell visco-elastic model, a relationship is established between deformation rates and stresses. The developed model allows to take into account the metal softening during a pause after hot deformation. The resulting mathematical model is tested by experiment on different steels at different temperatures of deformation. The process of steels softening is determined using plastometers. It is established experimentally that the model developed by 89 ... 93 % describes the rheology of the metal during hot deformation. The relationship between the components of the deformation rates and stresses is established, which allows to obtain a direct numerical solution of plastic deformation problems without FED iterative procedures, taking into account the real properties of the metal during deformation. As a result, the number of iterations and calculations has significantly decreased.
The simulation of the process of combined radial reverse extrusion of hollow parts with a flange has established two fundamentally different, in terms of the components of the kinematic modules, calculation schemes CDZ-1.i and CDZ-2.j, taking into conside ration the possible shape of the boundary of the section of a metal flow inside a workpiece. The comparison of the dependences of the optimal relative rate of metal outflow in the opposite direction for different schemes indicates significant differences in the resulting values in the course of the deformation process. The relevance of this study is due to making it easier to evaluate the use of the combined extrusion process to produce hollow parts with a flange while maintaining the required dimensions compared to simple deformation schemes. We have identified the lack of detailed studies into the technologies for the introduction of combined extrusion schemes, as well as the absence of technological recommendations for determining the force regime and the shape formation of a semi-finished article. The process of the combined extrusion of hollow parts with a flange was investiga ted, thereby selecting different types based on the nature of the metal flow depending on the geometric ratios of the deformation process. We have obtained experimental data on the gradual shape formation of a semi-finished product in the process of deformation at different geometric ratios. The limits of using estimation schemes of the process have been defined to obtain data on the increments in a semi-finished product, including in terms of predicting the formation of a shrinkage cavity in the bottom part. It is recommended that a condition of selecting the appropriate scheme should be the condition for a minimum value of the reduced pressure of deformation i < j. The resulting recommendations make it easier to predict the shape formation and the force mode of extrusion (a deviation from experimentally obtained data can be reduced to 10 %), which would contribute to evaluating the rationality of the combined extrusion processes while ensuring the required dimensions of a part
The method of upsetting of large ingots has been investigated in this work. The proposed method consists in upsetting of profiled workpieces with concave faces. An angle of the concave faces was 150°. A relative depth of the concave faces has been varied in range 15%…25% from workpiece's diameter. Strains effective and mean stresses in the longitudinal cross-section of the workpiece with concave faces after upsetting have been determined by FEM. A value of compressive stresses has been determined based on a parameter of the stress state. FEM allowed to find what a rational depth of the concave faces should be, which has to be 15 % from workpiece's diameter. Maximum closing of the internal defect take place for this depth of the concave faces. Results of the FEM have been tested by experimental investigations. It has been established that upsetting of the four-beam workpieces improved a quality of the massive parts.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.