The creation of gold surfaces modified by single- or double-stranded DNA self-assembled monolayers (SAMs) is shown to produce heterogeneous surface packing densities through the use of electrochemical studies coupled with fluorescence imaging. The modified surfaces created by direct adsorption of thiolate DNA [followed by passivation with mecaptohexanol (MCH)] resulted in regions covered by a monolayer of DNA SAM and other regions that were coated by large particles of DNA. The difference in fluorescence intensity measured from these regions was dramatic. More importantly, a regional variance in fluorescence intensity in response to electrochemical potential was observed: the large aggregates showing a significantly different modulation of fluorescence intensity than the monolayer-coated regions. Electrochemical desorption and detection of the fluorescently tagged DNA provided clear evidence of a complete surface modification. These studies have implications for biosensor/biochip development using DNA SAMs. A modification in the method used to produce the DNA SAMs resulted in a significantly different surface with much fewer aggregates and more significant electromodulation of the fluorescence intensity, though at much lower DNA surface density (ca. 1% of maximum theoretical coverage). This method for forming the modified surfaces has clear advantages over the currently accepted practice and emphasizes the importance of studying the nonaveraged nature of the sensor surface using in situ imaging tools like electrofluorescence microscopy.

This paper reports a simple electrochemical approach for the detection of the ubiquitous protein lysozyme using aptamer-modified electrodes. Anti-lysozyme DNA aptamers were immobilized on gold surfaces by means of self-assembly, for which the surface density of aptamers was determined by cyclic voltammetric (CV) studies of redox cations (e.g., [Ru(NH3)6]3+) bound to the surface via electrostatic interaction with the DNA phosphate backbone. Upon incubation of the electrode with a solution containing lysozyme, the CV response of surface-bound [Ru(NH3)6]3+ changed substantially, and the relative decrease in the integrated charge of the reduction peak can be tabulated as a quantitative measure of the protein concentration. It is significant that the on-chip protein/aptamer binding constant and the optimized surface density to achieve the best detection limit can be evaluated. This biosensor is label-free and offers an alternative, sensitive, and versatile method for protein detection, which is beneficial to the ever-growing interests of fabricating portable bioanalytical devices with simple electrical readout protocols.

The wetting property and evaporation behavior of ethanol-water mixtures of various concentrations on gold surfaces modified with 1-decanethiolate self-assembled monolayers (SAMs) were studied by digital contact angle analysis. It has been shown that the initial contact angle decreases monotonically with increased concentration of ethanol in the mixture. Evaporation studies revealed a general trend with a preliminary increase in contact angle accompanied with a decrease in contact area, then a constant contact angle accompanied with a slower, linear decrease in contact area. At the very beginning of the evaporation process, the contact angles showed a rapid decrease for the microdroplets of a binary mixture with equal volume fractions (i.e., 50% ethanol). Three distinct stages of the evaporation profile for the ethanol-water mixtures were observed, which differ from the inclusive "pinning" and "shrinking" behavior observed for the pure liquid case. Ultimately, the study makes possible the use of an evaporation profile to monitor the change in concentration of a binary system and allows a better understanding of the interactions between liquid microdroplets with solid substrates.

Mucin 1 (MUC1) is a glycoprotein expressed on most epithelial cell surfaces, which has been confirmed as a useful biomarker for the diagnosis of early cancers. In this paper, we report an aptamer-based, quantitative detection protocol for MUC1 using a 3-component DNA hybridization system with quantum dot (QD)-labeling: in the absence of MUC1 peptides, strong fluorescence is observed upon mixing the three specially designed DNA strands (quencher, QD-labeled reporter, and the MUC1 aptamer stem); in the presence of MUC1 peptides, a successive decrease in fluorescence intensity is detected since the MUC1 peptide binds to the aptamer strand in such a way to allow the quencher and fluorescence reporter to be brought into close proximity (which leads to the occurrence of fluorescence resonance energy transfer, FRET, between the quencher and QD). The detection limit for MUC1 with this novel approach is in the nanomolar (nM) level, and a linear response can be established for the approximate range found in blood serum. This study also provided further insight into the aptamer/analyte binding site/mode for MUC1, which augments the possibility of improving this detection methodology for the early diagnosis of different types of epithelial cancers of large populations.