This study aims at the interpretation of the adverse effects of the secondary products in two types of rocks during their performance as concrete aggregates. Serpentinised peridotites contain serpentine, as the dominant secondary phase, which creates low microroughness on the particles and therefore unfavorable surfaces for cement paste to adequately adhere to. Moreover, its soft and platy nature contributes to the development of platy defects along the contacts of the aggregate particles with the cement paste. Poor adherence of the paste, failures along the contacts of the aggregate particles and potential propagation of the defects into the concrete during curing (and perhaps subsequently in-service) explain the poor performance of highly serpentinised rocks as concrete aggregates. Andesites show a different composition with a variety of secondary products including albite, chlorite, calcite, Fe-oxides and clay minerals. The role of all these products was investigated and it appears that only smectite is important, as even small amounts of it may be detrimental to the quality of the rocks as concrete aggregates. It is likely that abnormal hydration reactions and considerable swelling of the smectite result in the appearance of defects in the concrete, hence contributing to its low performance.

This paper examines the effect of the aggregate type on concrete strength, and more specifically, how the petrographic characteristics of various aggregate rocks as well as their physicomechanical properties influences the durability of C 25/30 strength class concrete. The studied aggregate rocks were derived from Veria-Naousa and Edessa ophiolitic complexes as well as granodiorite and albitite rocks from their surrounding areas in central Macedonia (Greece). Concretes were produced with constant volume proportions, workability, mixing and curing conditions using different sizes of each aggregate type. Aggregates were mixed both in dry and water saturated states in concretes. Six different types of aggregates were examined and classified in three district groups according to their physicomechanical properties, petrographic characteristics and surface texture. The classification in groups after the concrete compressive strength test verified the initial classification in the same three groups. Group I (ultramafic rocks) presented the lowest concrete strengths, depending on their high alteration degree and the low mechanical properties of ultramafic aggregates. Group II (mafic rocks and granodiorite) presented a wide range of concrete strengths, depending on different petrographic characteristics and mechanical properties. Group III (albite rocks) presented the highest concrete strengths, depending on their lowest alteration degree and their highest mechanical properties. Therefore, mineralogy and microstructure of the coarse aggregates affected the final strength of the concrete specimens.factor for the quality of concrete. For the same quality cement, different lithotypes of coarse aggregates characterized by different micro-roughness, mineralogical composition, structure and compressive strength may result in different concrete compressive strength [10,11].Mineralogical composition of the aggregates, and more specifically their alteration degree, strongly influence their mechanical behavior and their in-service performance [10,[12][13][14][15][16][17]. Increased percentages of certain secondary minerals negatively affect the physical, as well as the mechanical properties of aggregates due to their smooth layers, cleavage and platy or fibrous crystal habit [10,17], which have an adverse effect on their performance as concrete aggregates [10]. The increased number of construction failures has highlighted the importance of understanding that mineralogy is a mean to diagnose problems in engineering constructions. The physico-mechanical properties of rocks used as aggregates are the most significant parameters in any application and in their classification for various engineering purposes. Physicomechanical properties depend on the petrographic characteristics (mineralogical composition, texture, size, shape and arrangement of mineral grains, nature of grains contact and degree of grain interlocking), alteration and deformation degree of the source rock [18][19][20][21][22].Nowadays, many researchers [11,[23][24][25]...

This paper investigates the effect of alteration on the physicomechanical properties of igneous rocks used as aggregates, from various areas from Greece. The studied lithologies include serpentinized dunites, serpentinized harzburgites, serpentinized lherzolites, metamorphic gabbros, diabases, dacites and andesites. Quantitative petrographic analysis shows that the tested samples display various percentages of secondary phyllosilicate minerals. Mineral quantification of the studied rock samples was performed by using the Rietveld method on X-ray diffraction patterns. The samples were also tested to assign moisture content (w (%)), total porosity (n t (%)), uniaxial compressive strength (UCS (MPa)) and Los Angeles abrasion test (LA (%)). The influence of secondary phyllosilicate minerals on the physicomechanical behavior of the tested samples was determined using regression analysis and their derived equations. Regression analysis shows a positive relationship between the percentage of the phyllosilicate minerals of the rocks and the moisture content as well as with the total porosity values. In mafic and ultramafic rock samples, the relationships between the secondary phyllosilicate minerals and their physicomechanical properties have shown that the total amount of the secondary phyllosilicate minerals results negatively on their physicomechanical properties. On the other hand, the low percentage of phyllosilicate minerals in volcanic rocks can't be able to define their engineering properties.

This paper examined three different types of recycled materials, such as beer green glass, waste tile, and asphalt, which will be used in different mixtures in order to prepare concrete specimens and, more specifically, their effect on concrete strength and how the petrographic characteristics of various recycled materials influenced the durability of C25/30 strength class concrete. Particular emphasis was placed on the effect of artificial microroughness of glassy and smooth surfaces of recycled materials on their final concrete strength. The concrete strength values do not show great variance, but their limited differences have been qualitatively interpreted by a new promising petrographic methodology, including the study of the surface texture of the used aggregate materials. Concretes are produced with constant volume proportions, workability, mixing, and curing conditions while using different sizes of each aggregate type. The aggregates were mixed both in dry and water saturated states in concretes. Concretes that are made by a mixture of beer green glass with quartz primer, as well as of tile with quartz primer, presented the optimum possible results of the compressive strength.

This case study investigates the influence of the mineralogical composition of ultramafic rocks derived from two ophiolite complexes from Greece (Veria-Naousa and Gerania) on their mechanical, physical and physicochemical properties. The investigated lithologies include lherzolite, harzburgite, dunite and olivine-orthopyroxenite with variable degrees of alteration. The ratio of secondary minerals to primary minerals (SEC/PR) of the studied ultramafic rocks shows good correlations with their physical, physicochemical and mechanical properties, suggesting that alteration has a negative effect on the engineering performance of the ultramafic rocks. Among the secondary minerals, serpentine plays the most critical role in determining the moisture content, the total porosity and hence the soundness of the host rocks, due to its phyllosilicate structure, which allows more water/solutions to be captured. The high percentage of serpentine creates surfaces of weakness, and as a result, it decreases the rock strength. The low microtopography of highly serpentinized rocks results in their reduced mechanical performance.