The advances in personalised medicine increased the demand for a fast, accurate and reliable production method of tablets that can be digitally controlled by healthcare staff. A flexible dose tablet system is presented in this study that proved to be suitable for immediate and extended release tablets with a realistic drug loading and an easy-to-swallow tablet design. The method bridges the affordable and digitally controlled Fused Deposition Modelling (FDM) 3D printing with a standard pharmaceutical manufacturing process, Hot Melt Extrusion (HME). The reported method was compatible with three methacrylic polymers (Eudragit RL, RS and E) as well as a cellulose-based one (hydroxypropyl cellulose, HPC SSL). The use of a HME based pharmaceutical filament preserved the linear relationship between the mass and printed volume and was utilized to digitally control the dose via an input from computer software with dose accuracy in the range of 91-95%. Higher resolution printing quality doubled the printing time, but showed a little effect on in vitro release pattern of theophylline and weight accuracy. Physical characterization studies indicated that the majority of the model drug (theophylline) in the 3D printed tablet exists in a crystal form. Owing to the small size, ease of use and the highly adjustable nature of FDM 3D printers, the method holds promise for future individualised treatment.

2 ABSTRACTPurpose. The fabrication of a ready-to-use immediate release tablets via 3D printing provides a powerful tool to on-demand individualization of dosage form. This work aims to adapt a widely used pharmaceutical grade polymer, polyvinylpyrrolidone (PVP), for instant on-demand production of immediate release tablets via FDM 3D printing.Methods. Dipyridamole or theophylline loaded filaments were produced via processing a physical mixture of API (10%) and PVP in the presence of plasticizer through hot-melt extrusion (HME). Computer software was utilized to design a capletshaped tablet. The surface morphology of the printed tablet was assessed using scanning electron microscopy (SEM). The physical form of drug and its integrity following an FDM 3D printing were assessed using x-ray powder diffractometry (XRPD), thermal analysis and HPLC. In vitro drug release studies for all 3D printed tablets were conducted in a USP II dissolution apparatus.Results. Bridging 3D printing process with HME in the presence of a thermostable filler, talc, enabled the fabrication immediate release tablets at temperatures as low as 110 o C. The integrity of two models drugs was maintained following HME and FDM 3D printing. XRPD indicated that a portion of the loaded theophylline remained crystalline in the tablet. The fabricated tablets demonstrated excellent mechanical properties, acceptable in-batch variability and an immediate in vitro release pattern. Conclusions.Combining the advantages of PVP as an impeding polymer with FDM 3D printing at low temperatures, this approach holds a potential in expanding the spectrum of drugs that could be used in FDM 3D printing for on demand manufacturing of individualised dosage forms.

Despite its relatively limited resolution, FDM 3D printing proved to be a suitable platform for a single-process fabrication of delayed release tablets. This work reveals the potential of dual FDM 3D printing as a unique platform for personalising delayed release tablets to suit an individual patient's needs.

Abstract*Corresponding author: MAlbedAlhnan@uclan.ac.uk This work aims to employ fused deposition modelling 3D printing to fabricate immediate release pharmaceutical tablets with various model drugs. It investigates the addition of nonmelting filler to methacrylic matrix to facilitate FDM 3D printing and explore the impact of i) the nature of filler, ii) compatibility with the gears of the 3D printer and, and iii) polymer: filler ratio on the 3D printing process. A specially developed filament based on pharmaceutically approved methacrylic polymer (Eudragit E) and thermally stable filler, TCP (tribasic calcium phosphate) was optimised. Four model drugs (with different physicochemical properties were included into ready-to-use mechanically stable tablets with immediate release properties. Amongst the investigated fillers in this work, directly compressible lactose, spray-dried lactose and microcrystalline cellulose showed a level of degradation at 135 o C whilst talc and TCP allowed consistent flow of the filament and a successful 3D printing of the tablet. Following the two thermal processes (hot melt extrusion (HME) and fused deposition modelling (FDM) 3D printing), drug contents were 94.22%, 88.53%, 96.51% and 93.04% for 5-ASA, captopril, theophylline and prednisolone respectively. XRPD indicated that a fraction of 5-ASA, theophylline and prednisolone remained in the crystalline form whilst captopril was in amorphous form. By combining the advantages of thermally stable pharmaceutically approved polymers and fillers, this unique approach provides a low cost production method for on demand manufacturing of individualised dosage forms.

Hypertension and dyslipidaemia are modifiable risk factors associated with cardiovascular diseases (CVDs) and often require a complex therapeutic regimen. The administration of several medicines is commonly associated with poor levels of adherence among patients, to which World Health Organisation (WHO) proposed a fixed-dose combination unit (polypill) as a strategy to improve adherence. In this work, we demonstrate the fabrication of patient-specific polypills for the treatment of CVDs by fused deposition modelling (FDM) 3D printing and introduce a novel solution to meet critical quality attributes. The construction of poly(vinyl alcohol) (PVA)-based polypills containing four model drugs (lisinopril dihydrate, indapamide, rosuvastatin calcium and amlodipine besylate) was revealed for the first time. The impact of tablet architecture was explored using multi-layered and unimatrix structures. The novel approach of using distilled water as a 'temporary co-plasticiser' is reported and was found to significantly lower the extruding (90°C) and 3D printing (150°C) temperatures from 170°C and 210°C respectively, with consequent reduction in thermal stress to the chemicals. XRD indicated that lisinopril dihydrate and amlodipine besylate maintained their crystalline form while indapamide and rosuvastatin calcium were essentially amorphous in the PVA tablets. From the multilayer polypills, the release profile of each drug was dependent on its position in the multilayer.In addition to the multilayer architecture offering a higher flexibility in dose titration and a more adaptive solution to meet the expectations of patient-centred therapy, we identify that it also allows orchestrating the release of drugs of different physicochemical characteristics. Adopting such an approach opens up a pathway towards low-cost multidrug delivery systems such as tablets, stents or implants for wider range of globally approved actives.