Metallic Zn alloys have recently gained interest as potential candidates for developing platforms of bioresorbable vascular stents (BVS). Previous studies revealed that Mg alloys used for BVS can degrade too early, whereas PLLA materials may fail to provide effective scaffolding properties. Here we report on results of a new bioresorbable, metallic stent made from a Zn-Ag alloy studied in a porcine animal model of thrombosis and restenosis. While the tensile strength (MPa) of Zn-3Ag was higher than that of PLLA and resembled Mg’s (WE43), fracture elongation (%) of Zn-3Ag was much greater (18-fold) than the PLLA’s or Mg alloy’s (WE43). Zn-3Ag exposed to HAoSMC culture medium for 30 days revealed degradation elements consisting of Zn, O, N, C, P, and Na at a 6 nm surface depth. Platelet adhesion rates and blood biocompatibility did not differ between Zn-3Ag, PLLA, Mg (WE43), and non-resorbable Nitinol (NiTi) stent materials. Balloon-expandable Zn-3Ag alloy BVS implanted into iliofemoral arteries of 15 juvenile domestic pigs were easily visible fluoroscopically at implantation, and their bioresorption was readily detectable via X-ray over time. Histologically, arteries with Zn-3Ag BVS were completely endothelialized, covered with neointima, and were patent at 1, 3, and 6 months follow-up with no signs of stent thrombosis. Zn-3Ag alloy appears to be a promising material platform for the fabrication of a new generation of bioresorbable vascular stents.

Zinc alloys have recently been researched intensely for their great properties as bioabsorbable implants for osteosynthesis. Pure zinc (Zn) itself has relatively poor strength, which makes it insufficient for most clinical use. Research has already proven that the mechanical strength of zinc can be enhanced significantly by alloying it with silver. This study evaluated zinc silver alloys (ZnAg) as well as novel zinc silver titanium alloys (ZnAgTi) regarding their mechanical properties for the use as bioabsorbable implants. Compared to pure zinc the mechanical strength was enhanced significantly for all tested zinc alloys. The elastic properties were only enhanced significantly for the zinc silver alloys ZnAg6 and ZnAg9. Regarding target values for orthopedic implants proposed in literature, the best mechanical properties were measured for the ZnAg3Ti1 alloy with an ultimate tensile strength of 262 MPa and an elongation at fracture of 16%. Besides the mechanical properties, the corrosion rates are important for bioabsorbable implants. This study tested the corrosion rates of zinc alloys in PBS solution (phosphate buffered solution) with electrochemical corrosion measurement. Zinc and its alloys showed favorable corrosion rates, especially in comparison to magnesium, which has a much lower degradation rate and no buildup of hydrogen gas pockets during the process. Altogether, this makes zinc alloys highly favorable for use as material for bioabsorbable implants for osteosynthesis.

Background According to early clinical trials, vascular brachytherapy performed prior to or shortly after angioplasty is very effective in reducing restenosis rates. The purpose of this study was to investigate the effects of a novel radioactive catheter that allows simultaneous balloon angioplasty and beta-particle irradiation in the prevention of restenosis. Material and MethodsThe balloon surface of an angioplasty catheter was impregnated with the radioisotope 32 P. Dosimetry calculations using a Monte Carlo method were performed at a radial distance of 0·2 mm from the balloon surface. Rabbit iliac arteries were dilated and simultaneously irradiated with a dose of 20 Gy delivered to the adventitia. Control arteries were only dilated and not irradiated. Neointimal areas, cell numbers and the perimeter of the arteries were measured by histomorphometry after 6 weeks.Results Neointima formation was reduced after balloon dilatation and simultaneous beta-particle irradiation using the 32 P impregnated angioplasty catheter as compared to balloon dilatation alone with a non-impregnated catheter (0·09 0·06 vs 0·27 0·09 mm 2 neointimal area and 168 45 vs 360 133 cells/0·05 mm 2 neointima, P<0·001 vs control, respectively). In addition, balloon dilatation with the 32 P impregnated angioplasty catheter increased the vessel perimeter as compared to balloon dilatation with a non-impregnated catheter (4·7 0·2 vs 3·9 0·3 mm, P<0·001 vs control).Conclusions Simultaneous balloon dilatation and vascular brachytherapy with a novel 32 P impregnated angioplasty catheter markedly reduces restenosis in vivo by preventing neointimal hyperplasia and constrictive vascular remodelling.

Biomaterials made of zinc have been widely described to be antioxidative, hypothrombogenic, antiinflammatory and antiproliferative. Additionally in vivo zinc is toxic only in high concentrations and can completely be metabolized in vivo. Due to these properties zinc based vascular stents might be able to reduce the rate of restenosis in comparison to bare metal stents and zinc stents might be also able to limit the foreign body reaction. In the presented study we tested the biocompatibility and degradability of a stent made of zinc and characterized by a closed-cell-design to achieve high opening force and to increase stent stiffness. After 100 days of enzymatic and hydrolytic degradation in 15 ml blood serum (fetal calf serum) a significant loss of weight (1.72 wt% ) was measured. Zinc was compared to other metals in terms of degradation rates. After six weeks of incubation in physiologic sodium chloride solution zinc showed the slowest degradation time, 6 times less than stainless steel and 4 times less than magnesium. In the tests for cytotoxic effects the degraded zinc stent caused no changes in the LDH-release and cell membrane integrity (3T3 cells, mouse fibroblasts) respectively, in the cell activity/proliferation (MTS assay) and in the morphological characteristics of the cells and cell layers in comparison to the control material (polystyrene). Based on these results the tested zinc stent proved to be non-cytotoxic and to be characterized by degradation characteristics which might be advantageous in comparison to magnesium and stainless steel.

No abstract