The geopolymer binder is a relatively new class of inorganic binding material of elevated mechanical strength and good chemical properties. This can be produced using clay minerals or byproducts of the industrial processes, such as metakaolin, fly-ash and blast furnace slag. In this work, geopolymers were produced by alkaline activation of a Brazilian fly-ash with simple and compound solutions (NaOH and NaOH + Na 2 SiO 3). The hardened specimens presented values of the mechanical strength close to 48 MPa when the activator used presented SiO 2 /Na 2 O ration close to 1.0 after 24 h of curing at 65 °C. The increase of the temperature to 90 °C favored the reactions of the N-AS -H gel (geopolymer) formation and compression strength increased to values close to 90 MPa after 24 h. It has been found that physical properties, such as density and porosity, varied when different SiO 2 /Na 2 O rations was present in alkaline solutions. Time, temperature of curing and particle size of fly-ash modified the mechanical and physical proprieties of hardened inorganic binder. Was observed the diffraction phases related to zeolitic phases and carbonate new bands of absorption were related to reactions of Na2O in excess with atmospheric CO 2. The variation of SiO 2 /Na 2 O modified the microstructural of the hardened specimens.
INTRODUÇÃONas últimas décadas houve um crescente aumento tecnológico relacionado com pesquisas sobre novos materiais. Esses novos materiais devem ser produzidos com melhorias em suas aplicações e, se possível, com uma preocupação em relação ao impacto ambiental causado por eles. A indústria da construção civil está dentre os setores que mais degradam o meio ambiente durante a produção dos materiais necessários para implantação [1,2]. O cimento Portland (CP) é um dos materiais mais utilizados na indústria da construção civil e sua fabricação promove a liberação de elevadas quantidades de CO 2 para a atmosfera e consome grande quantidade de energia durante a produção do clínquer [3]. De acordo com o relatório produzido em 2013 pelo Sindicato Nacional da Indústria do Cimento, no mesmo ano, o Brasil consumiu cerca de 70000 toneladas de cimento Portland [3]. Devido ao grande consumo desse material e com sua impactante destruição ambiental um novo ligante capaz de competir com o CP como ligante na construção civil se faz necessário [4][5][6].Uma forma de minimizar esse impacto ambiental é a utilização de materiais álcali-ativados [4]. Esses materiais, também conhecidos como geopolímeros ou polímeros inorgânicos são materiais ricos em aluminossilicatos, apresentando estruturas que variam de acordo com a composição química:Esses polímeros inorgânicos apresentam grandes vantagens quando comparados ao CP. Entre as várias propriedades podemos destacar a elevada resistência mecânica, ganho de resistência mecânica em curtos períodos de cura, resistência a ataques ácidos e de sulfatos, resistência a ciclos de gelo-degelo, estabilidade estrutural quando submetidos a elevadas temperaturas, entre outros [5,[9][10][11][12][13][14][15][16]. O termo geopolímero foi primeiramente utilizado pelo francês Davidovits na década de 1970 e o processo se assemelha ao mecanismo de obtenção dos polímeros orgânicos [17,18]. A composição mineralógica do material de partida, temperatura e tempo de cura, quantidade de água e a concentração dos compostos presentes na solução alcalina ativadora são os principais parâmetros controlados durante a produção desses materiais [19][20][21][22][23]. A obtenção desse material pode ser feita por meio da ativação alcalina de precursores ricos e aluminossilicatos, tais como metacaulim,
INTRODUÇÃOAs pesquisas de materiais aplicáveis nas áreas da medicina trazem um aumento na qualidade de vida de pessoas que necessitam de tratamentos mais eficazes ou soluções para problemas graves. Pesquisas relacionadas à descoberta e melhoramento de materiais usados nas diversas áreas médicas -materiais cirúrgicos, materiais para substituições de tecidos ósseos -aumentam cada dia mais devido às necessidades e o aumento do número de enfermidades. Lesões onde partes do tecido ósseo são removidas são normalmente encontradas em acidentes. Os membros são geralmente retirados para se evitar complicações posteriores ou quando a recuperação dessas partes afetadas é impossível. Esse tipo de procedimento é comum nos hospitais do Brasil representando um grande trauma para o paciente que necessitará se adaptar a novas formas de vida, dependendo de membros artificiais que substituirão as partes lesionadas [1,2]. A busca por novos materiais que substituam essas partes lesionadas é motivo de novas pesquisas nas áreas de materiais [3]. Os materiais obtidos a partir dessas pesquisas podem ser metálicos, poliméricos, compósitos ou cerâmicos, entretanto, todos eles devem apresentar características essenciais como: Elevada resistência mecânica, elevada resistência à fadiga, nenhuma ou baixa toxicidade, baixa solubilidade nos fluidos corpóreos e, se possível, ter boa compatibilidade com o sistema biológico onde será implantado com o intuito de se diminuir a rejeição pós-cirúrgica [2,4]. Vários materiais possuem características ideais para serem utilizados na construção de próteses substituintes de tecidos ósseos, porém, materiais a base de fosfato de cálcio promovem a sua regeneração (osteocondução) e são usados na confecção de próteses e enxertos [2].Efeito da temperatura em processos de sinterização de pós de hidroxiapatita
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.